455215
82
Zoom out
Zoom in
Previous page
1/100
Next page
Additional information
13
82
En
Other audio problems
Symptom Remedy
Broadcast stations cannot be
selected automatically, or
there is considerable noise in
radio broadcasts.
For FM broadcasts
• Fully extend the FM wire antenna, adjust the position for best reception and secure to a wall, etc.
• Use an outdoor antenna for better reception (see page 23).
For AM broadcasts
• Adjust the position and direction of the AM antenna.
• Use an outdoor antenna for better reception (see page 23).
• Noise may be caused by interference from other equipment, such as a fluorescent light, motor,
etc. Switch off or move the other equipment, or move the AM antenna.
A multichannel DVD source
appears to be downmixed to 2
channels during playback.
• Make sure that the multichannel analog inputs are selected (see Selecting the multichannel analog
inputs on page 58).
Noise is output when scanning
a DTS CD.
• This is not a malfunction of the receiver. The scan function of your player alters the digital
information, making it unreadable, resulting in noise being output. Lower the volume when
scanning.
When playing a DTS format LD
there is audible noise on the
soundtrack.
• Make sure that the input signal type is set to DIGITAL (see Choosing the input signal on page 33).
Can’t record audio. • You can only make a digital recording from a digital source, and an analog recording from an
analog source.
• For digital sources, make sure that what you’re recording isn’t copy protected.
• Check that the OUT jacks are properly connected to the recorders input jacks (see Connecting
analog audio sources on page 20).
Subwoofer output is very low. • To route more signal to the subwoofer, set it to PLUS or set the front speakers to SMALL (see
Speaker Setting on page 48).
Everything seems to be set up
correctly, but the playback
sound is odd.
• The speakers may be out of phase. Check that the positive/negative speaker terminals on the
receiver are matched with the corresponding terminals on the speakers (see Connecting the
speakers on page 21).
The PHASE CONTROL feature
doesn’t seem to have an
audible effect.
• If applicable, check that the lowpass filter switch on your subwoofer is off, or the lowpass cutoff is
set to the highest frequency setting. If there is a PHASE setting on your subwoofer, set it to 0º (or
depending on the subwoofer, the setting where you think it has the best overall effect on the sound).
• Make sure the speaker distance setting is correct for all speakers (see Speaker Distance on
page 50).
Noise or hum can be heard
even when there is no sound
being input.
• Check that personal computers or other digital components connected to the same power source
are not causing interference.
There seems to be a time lag
between the speakers and the
output of the subwoofer.
• See Automatically setting up for surround sound (Auto MCACC) on page 10 to set up your system
again using MCACC (this will automatically compensate for a delay in the subwoofer output).
Can’t use the SR+ features. • Make sure that HDMI Control is set to OFF (see Setting the HDMI Control mode on page 65).
The maximum volume
available (shown in the front
panel display) is lower than the
+12dB maximum.
• This is not a malfunction. If the levels in Channel Level on page 49 have been adjusted, the
maximum volume will change accordingly.
VSX-1018AH_KU.book Page 82 Monday, March 10, 2008 4:51 PM
82


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer VSX-1018AH-K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer VSX-1018AH-K in the language / languages: English as an attachment in your email.

The manual is 3,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer VSX-1018AH-K

Pioneer VSX-1018AH-K User Manual - English - 37 pages

Pioneer VSX-1018AH-K User Manual - German - 96 pages

Pioneer VSX-1018AH-K User Manual - German - 37 pages

Pioneer VSX-1018AH-K User Manual - Dutch - 37 pages

Pioneer VSX-1018AH-K User Manual - Dutch - 96 pages

Pioneer VSX-1018AH-K User Manual - French - 96 pages

Pioneer VSX-1018AH-K User Manual - French - 37 pages

Pioneer VSX-1018AH-K User Manual - Italian - 96 pages

Pioneer VSX-1018AH-K User Manual - Italian - 37 pages

Pioneer VSX-1018AH-K User Manual - Swedish - 186 pages

Pioneer VSX-1018AH-K User Manual - Spanish - 96 pages

Pioneer VSX-1018AH-K User Manual - Spanish - 37 pages

Pioneer VSX-1018AH-K User Manual - Norwegian - 186 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info