Manual Pioneer AVIC-F9880DAB (page 64 of 87) (English)

649253

Zoom out

Zoom in

1/87

Adjusting the speaker output

levels nely

Fine adjustments of the speaker output level can be made by

listening to audio output.

1 Display the “Audio” setting screen.

 Refer to Displaying the “Audio” setting screen on page 63

2 Touch [Speaker Level].

3 Touch [<] or [>] to select the listening position

if necessary.

The following items are available:

Off, Front-L, Front-R, Front, All.

The default setting is “Off”.

If you change the setting for the listening position, the

output levels of all the speakers will change according to the

setting.

4 Touch [<] or [>] to adjust the speaker output

level.

p “–24” dB to “10” dB is displayed as the level to be corrected

is increased or decreased.

The following items are available:

Front Left, Front Right, Rear Left, Rear Right, Subwoofer

If the Auto EQ measurement has been done, the result of the

Auto EQ measurement will be applied by touching [Apply

Auto EQ] (the results are also applied to some settings

simultaneously).

Adjusting the time alignment

By adjusting the distance from each speaker to the listening

position, time alignment is able to correct the time required for

sound to reach the listening position.

1 Measure the distance between the head of the

listener and each speaker unit.

2 Display the “Audio” setting screen.

 Refer to Displaying the “Audio” setting screen on page 63

3 Touch [Time Alignment].

4 Touch [<] or [>] to select the listening position

if necessary.

The following items are available:

Off, Front-L, Front-R, Front, All.

The default setting is “Off”.

If you change the listening position setting, the distance

value of all the speakers will change in conjunction with the

setting.

5 Touch [<] or [>] to input the distance between

the selected speaker and the listening position.

The following items are available:

Front Left, Front Right, Rear Left, Rear Right, Subwoofer

You can input the value between 0 cm and 500 cm.

p The distance can be adjusted manually only when the listen-

ing position setting is set to “Front-L” or “Front-R”.

If the Auto EQ measurement has been done, the result of the

Auto EQ measurement will be applied by touching [Apply

Auto EQ] (the results are also applied to some settings

simultaneously).

 If you touch [TA On], the time alignment is turned

off mandatorily.

Using the equaliser

Recalling equaliser curves

There are multiple equalizer curves that you can easily recall at

any time. The equalizer curves you can recall are as follows:

S.Bass, Powerful, Natural, Vocal, Flat, Custom1 and Custom2

The default setting is “Powerful”.

1 Display the “Audio” setting screen.

 Refer to Displaying the “Audio” setting screen on page 63

2 Touch [Graphic EQ].

3 Touch the equalizer curve name.

Customising the equaliser curves

p If the preset equalizer curve other than “Custom1” or

“Custom2” is modified, the equalizer curve settings in

“Custom1” will be overwritten.

If the equalizer curve stored in “Custom1” or “Custom2” is

modified, each stored curve will be overwritten.

1 Display the “Audio” setting screen.

 Refer to Displaying the “Audio” setting screen on page 63

2 Touch [Graphic EQ].

3 Select a curve that you want to use as the basis

of customising.

4 Touch the frequency for which you want to

adjust the level.

p If you touch “Custom1” or “Custom2”, recall the equalizer

curve currently stored in “Custom1” or “Custom2”.

If you trail a finger across the bars of multiple equaliser

bands, the equaliser curve settings will be set to the value of

the touched point on each bar.

Setting the auto-adjusted equaliser

You can set the auto-adjusted equalizer to suit the vehicle’s

acoustics. To use this function, the Auto EQ measurement must

be done in advance.



Refer to Adjusting the equaliser curve automatically (Auto EQ)

on page 64

The default setting is “Off”.

1 Display the “Audio” setting screen.

 Refer to Displaying the “Audio” setting screen on page 63

2 Touch [Auto EQ&TA] to switch “On” or “Off”.

Adjusting the equaliser curve

automatically (Auto EQ)

By measuring the vehicle’s acoustics, the equaliser curve can be

adjusted automatically to suit the vehicle interior.

WARNING

A loud tone (noise) may be emitted from the speakers when

measuring the vehicle’s acoustics. Never perform Auto EQ

measurement while driving.

CAUTION

 Thoroughly check the conditions before performing Auto

EQ, as the speakers may be damaged if this is performed

under the following conditions:

—

When the speakers are incorrectly connected. (For exam-

ple, when a rear speaker is connected as a subwoofer

output.)

—

When a speaker is connected to a power amp delivering

output higher than the speaker’s maximum input power

capability.



If a microphone for acoustical measurement (sold

separately) is not placed in an appropriate location, the

measurement tone may become loud and measurement

may take a long time, resulting in battery drainage. Be sure

to place the microphone in the specified location.

Before operating the Auto EQ

function

 Perform Auto EQ in as quiet a place as possible, with the

vehicle engine and air conditioning switched off. Also, cut

< CRB4818-B >

Audio adjustments

Hello, I have read the documentation and I cannot change the langagefrom German to French for vocal navigation. In Parameters, I can change , but without modification on navigation. Ok for radio or screnn. Submitted on 9-3-2019 at 09:56
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer AVIC-F9880DAB in the language / languages: English as an attachment in your email.

The manual is 16,71 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer AVIC-F9880DAB

Pioneer AVIC-F9880DAB Installation Guide - English, German - 204 pages

Pioneer AVIC-F9880DAB User Manual - German - 95 pages

Pioneer AVIC-F9880DAB Installation Guide - Dutch - 204 pages

Pioneer AVIC-F9880DAB User Manual - Dutch - 91 pages

Pioneer AVIC-F9880DAB Installation Guide - French - 204 pages

Pioneer AVIC-F9880DAB User Manual - French - 93 pages

Pioneer AVIC-F9880DAB Installation Guide - Italian, Spanish - 204 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Pioneer AVIC-F9880DAB Manual

Product: