649253
62
Zoom out
Zoom in
Previous page
1/87
Next page
62
You can only update the firmware when the vehicle is
stopped and the handbrake is engaged.
1 Download the firmware update files into your
computer.
2 Connect a blank (formatted) storage device
to your computer, and then locate the correct
update file and copy it onto the storage device.
3 Set the external storage device to this product.
Refer to Inserting and ejecting an SD memory card on page
6
Refer to Plugging and unplugging a USB storage device on
page 6
4 Turn the source off.
Refer to Selecting a source on page 9
5 Display the “System” setting screen.
Refer to Displaying the “System” setting screen on page
58
6 Touch [System Information].
7 Touch [Firmware Update].
8 Touch [Continue] to display the data transfer
mode.
Follow the on-screen instructions to finish updating the
firmware.
p
If an error message appears on the screen, touch the display
and perform the above steps again.
Checking sensor learning status
and driving status
You can check the sensor learning status, such as the degree of
learning. You can also check the current sensor values and the
total number of speed pulses.
1 Display the “System” setting screen.
Refer to Displaying the “System” setting screen on page
58
2 Touch [System Information].
3 Touch [3D Calibration Status].
Clearing the status
You can delete the learned results stored in the sensor.
1 Display the “3D Calibration Status” screen.
2 Touch [Distance] or [Speed Pulse], and then
touch [Yes].
3 Touch [Learning] and then touch [Reset All].
p Touch [Reset All] to reset the sensor after changing the
installation position or angle.
p
If you touch [Reset Distance], all learned results stored in
Distance” are cleared.
Checking the connections of
leads
Check that the leads are properly connected between this
product and vehicle.
1 Display the “System” setting screen.
Refer to Displaying the “System” setting screen on page
58
2 Touch [System Information].
3 Touch [Connection Status].
GPS Antenna
Displays the connection status of the GPS aerial (“OK” or
NOK”) and the reception sensitivity.
p
If reception is poor, please change the installation position
of the GPS aerial.
Positioning Status
Displays the positioning status (3D positioning, 2D posi-
tioning, or no positioning), the number of satellites used for
positioning (orange), and the number of satellites whose
signal has been received (yellow). If signals from more than
three satellites are received, the current location can be
measured.
Refer to Positioning technology on page 75
Installation
Indicates whether the installation position of this product
is correct or not. If installed correctly, “OK” appears. When
this product is installed at an extreme angle exceeding
the limitation of the installing angle, “NOK(Inst. Angle)
will be displayed. If the installation of this product is
continually changed and it is not firmly fixed into place,
NOK(Vibration)” will be displayed.
Speed Pulse
The speed pulse value detected by this product is shown.
Illumination
Displays the status of headlights or small lamps of the
vehicle.
Back Signal
When the gearstick is shifted to “R” (reverse position), the
signal switches to “High” or “Low”. The signal displayed will
vary depending on the vehicle.
Vehicle Bus(*1)
Displays the status of the vehicle bus adapter.
p
(*1) F88DAB/F80DAB/F980DAB/F9880DAB
< CRB4818-B >
System settings
62


Need help? Post your question in this forum.

Forumrules
1

Forum

pioneer-avic-f9880dab

Reset search

  • Hello, I have read the documentation and I cannot change the langagefrom German to French for vocal navigation. In Parameters, I can change , but without modification on navigation. Ok for radio or screnn. Submitted on 9-3-2019 at 09:56

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer AVIC-F9880DAB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer AVIC-F9880DAB in the language / languages: English as an attachment in your email.

The manual is 16,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer AVIC-F9880DAB

Pioneer AVIC-F9880DAB Installation Guide - English, German - 204 pages

Pioneer AVIC-F9880DAB User Manual - German - 95 pages

Pioneer AVIC-F9880DAB Installation Guide - Dutch - 204 pages

Pioneer AVIC-F9880DAB User Manual - Dutch - 91 pages

Pioneer AVIC-F9880DAB Installation Guide - French - 204 pages

Pioneer AVIC-F9880DAB User Manual - French - 93 pages

Pioneer AVIC-F9880DAB Installation Guide - Italian, Spanish - 204 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info