Manual Pioneer AVH-X2800BT (page 40 of 57) (English)

649371

Zoom out

Zoom in

1/57

Off, Front-L, Front-R, Front, All.

The default setting is “Off”.

“All” is not available when “Network Mode” is selected as

the speaker mode.

If you change the listening position setting, the output

levels of all the speakers will change in conjunction with the

setting.

5 Touch or to input the distance between

the selected speaker and the listening position.

p You can input the value every 2.5 cm (between 0 and 350

cm).

The following speakers are available:

Standard Mode: Front Left, Front Right, Rear Left, Rear Right,

Subwoofer

Network Mode: High Left, High Right, Mid Left, Mid Right,

Subwoofer

This function is available only when the listening position

setting is set to “Front-L” or “Front-R”.

To use this function, the vehicle’s acoustics must be meas-

ured in advance.

 If you touch [TA On], the time alignment is turned

off mandatorily.

Switching the time alignment

preset

1 Display the “Audio” setting screen.

 Refer to Displaying the “Audio” setting screen on page 38

2 Touch [Time Alignment Preset].

3 Touch the item.

 Initial (default):

Sets to the initial setting value.



ATA:

Reflects the result of “A-EQ&TA Measurement” to the

setting value.



Off:

Resets all setting values to 0.



Custom:

Sets to the value adjusted at “Time Alignment”.

When you adjust the time alignment, the preset item will

switch automatically to “Custom”.

“Custom” can be selected only when the listening position is

set to “Front-L” or “Front-R”.

Using the equaliser

Recalling equaliser curves

There are seven stored equaliser curves that you can easily recall

at any time. Here is a list of the equaliser curves:



S.Bass is a curve in which only low-pitched sound is boosted.



Powerful is a curve in which low- and high-pitched sounds

are boosted.



Natural is a curve in which low- and high-pitched sounds

are slightly boosted.



Vocal is a curve in which the midrange, which is the human

vocal range, is boosted.



Flat is a flat curve in which nothing is boosted.



Custom1 is an adjusted equaliser curve that you create. If

you select this curve, the effect is applied to all AV sources.



Custom2 is an adjusted equaliser curve that you create. If

you select this curve, the effect is applied to all AV sources.

The default setting is “Powerful”.

1 Display the “Audio” setting screen.

 Refer to Displaying the “Audio” setting screen on page 38

2 Touch [Graphic EQ].

3 Touch the equaliser.

Customising the equaliser curves

You can adjust the currently selected equaliser curve setting

as desired. Adjustments can be made with a 13-band graphic

equaliser.

If you make adjustments when a curve “S.Bass”, “Powerful”,

“Natural”, “Vocal”, or “Flat” is selected, the equaliser curve

settings will be changed to “Custom1” mandatorily.

If you make adjustments when the “Custom2” curve is

selected for example, the “Custom2” curve will be updated.

“Custom1” and “Custom2” curves can be created common

to all sources.

1 Display the “Audio” setting screen.

 Refer to Displaying the “Audio” setting screen on page 38

2 Touch [Graphic EQ].

3 Select a curve that you want to use as the basis

of customising.

4 Touch the frequency for which you want to

adjust the level.

p If you trail a finger across the bars of multiple equaliser

bands, the equaliser curve settings will be set to the value of

the touched point on each bar.

Setting the auto-adjusted equaliser

You can set the auto-adjusted equaliser to suit the vehicle’s

acoustics. To use this function, the vehicle’s acoustics must be

measured in advance.

The default setting is “Off”.



Refer to Adjusting the equaliser curve automatically (Auto EQ)

on page 40

To manually adjust the equaliser curve, set “Auto EQ&TA” to

“Off”.

1 Display the “Audio” setting screen.

 Refer to Displaying the “Audio” setting screen on page 38

2 Touch “[Auto EQ&TA] to switch “On” or “Off”.

Adjusting the equaliser curve

automatically (Auto EQ)

By measuring the vehicle’s acoustics, the equaliser curve can be

adjusted automatically to suit the vehicle interior.

WARNING

A loud tone (noise) may be emitted from the speakers when

measuring the vehicle’s acoustics. Never perform Auto EQ

measurement while driving.

CAUTION

 Thoroughly check the conditions before performing Auto

EQ, as the speakers may be damaged if this is performed

under the following conditions:



When the speakers are incorrectly connected. (For exam-

ple, when a rear speaker is connected as a subwoofer

output.)



When a speaker is connected to a power amp delivering

output higher than the speaker’s maximum input power

capability.



If a microphone for acoustical measurement (sold

separately) is not placed in an appropriate location, the

measurement tone may become loud and measurement

may take a long time, resulting in battery drainage. Be sure

to place the microphone in the specified location.

Before operating the Auto EQ

function

 Perform Auto EQ in as quiet a place as possible, with the

vehicle engine and air conditioning switched off. Also, cut

power to car phones or mobile phones in the vehicle, or

< CRB4721-B >

Audio adjustments

radio won’t stop scrolling after install a back up camera what am I supposed to do to stop it Submitted on 28-5-2020 at 23:44
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer AVH-X2800BT in the language / languages: English as an attachment in your email.

The manual is 13,69 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer AVH-X2800BT

Pioneer AVH-X2800BT Installation Guide - English, German - 48 pages

Pioneer AVH-X2800BT User Manual - German - 63 pages

Pioneer AVH-X2800BT Installation Guide - Dutch - 48 pages

Pioneer AVH-X2800BT User Manual - Dutch - 62 pages

Pioneer AVH-X2800BT Installation Guide - French - 48 pages

Pioneer AVH-X2800BT User Manual - French - 61 pages

Pioneer AVH-X2800BT Installation Guide - Italian, Spanish - 48 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Pioneer AVH-X2800BT Manual

Product: