649371
38
Zoom out
Zoom in
Previous page
1/57
Next page
38
3 Connect the USB storage device to this
product.
4 Turn the source off.
Refer to Selecting a source on page 9
5 Display the “System” setting screen.
Refer to Displaying the “System” setting screen on page
35
6 Touch [System Information].
7 Touch [Firmware Update].
8 Touch [Continue] to display the data transfer
mode.
p Follow the on-screen instructions to finish updating the
firmware.
p
This product will reset automatically after the firmware
update is completed if the update is successful.
p
If an error message appears on the screen, touch the display
and perform the above steps again.
Displaying the “Audio” setting
screen
1 Press .
2 Touch , and then .
The “Audio” setting screen appears.
Using fader/balance adjustment
1 Display the “Audio” setting screen.
Refer to Displaying the “Audio” setting screen on page 38
2 Touch [Fader/Balance].
p Only the balance can be adjusted when “Network Mode” is
selected as the speaker mode. Touch [Balance] and skip to
step 4.
3 Touch or to adjust the front/rear speaker
balance.
p Set “Front” and “Rear” to “0” when using a dual speaker
system.
4 Touch or to adjust the left/right speaker
balance.
You can also set the value by dragging the point
on the displayed table.
Switching sound muting/
attenuation
You can automatically mute or attenuate the AV source volume
and the iPhone application volume when the navigation outputs
the guidance voice.
1 Display the “Audio” setting screen.
Refer to Displaying the “Audio” setting screen on page 38
2 Touch [Mute Level].
3 Touch the item.
ATT (default):
The volume becomes 20 dB lower than the current volume.
Mute:
The volume becomes 0.
Off:
The volume does not change.
Adjusting source levels
SLA (source level adjustment) lets you adjust the volume level of
each source to prevent radical changes in volume when switch-
ing between sources.
p
Settings are based on the FM tuner volume level, which
remains unchanged.
p
This function is not available when the FM tuner is selected
as the AV source.
1 Compare the FM tuner volume level with the
level of the source.
2 Display the “Audio” setting screen.
Refer to Displaying the “Audio” setting screen on page 38
3 Touch [Source Level Adjuster].
4 Touch or to adjust the source volume.
p If you directly touch the area where the cursor can be moved,
the SLA setting will be changed to the value of the touched
point.
p
+4” to “–4” is displayed as the source volume is increased
or decreased.
p
The default setting is “0”.
Using the auto level control
This function corrects automatically the audio level difference
between the music files or the sources.
1 Display the “Audio” setting screen.
Refer to Displaying the “Audio” setting screen on page 38
2 Touch [Automatic Level Control].
3 Touch the item.
Off (default):
Turns the auto level control setting off.
Mode1:
Corrects a little the audio level difference between the music
files or the sources (for the narrow dynamic range audio
signal).
Mode2:
Corrects widely the audio level difference between the
music files or the sources (for the wide dynamic range audio
signal).
Adjusting loudness
This function compensates for deficiencies in the low-frequency
and high-frequency ranges at low volume.
The default setting is “Off”.
Audio adjustments
< CRB4721-B >
System settings Audio adjustments
38


Need help? Post your question in this forum.

Forumrules
1

Forum

pioneer-avh-x2800bt

Reset search

  • radio won’t stop scrolling after install a back up camera what am I supposed to do to stop it Submitted on 28-5-2020 at 23:44

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer AVH-X2800BT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer AVH-X2800BT in the language / languages: English as an attachment in your email.

The manual is 13,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer AVH-X2800BT

Pioneer AVH-X2800BT Installation Guide - English, German - 48 pages

Pioneer AVH-X2800BT User Manual - German - 63 pages

Pioneer AVH-X2800BT Installation Guide - Dutch - 48 pages

Pioneer AVH-X2800BT User Manual - Dutch - 62 pages

Pioneer AVH-X2800BT Installation Guide - French - 48 pages

Pioneer AVH-X2800BT User Manual - French - 61 pages

Pioneer AVH-X2800BT Installation Guide - Italian, Spanish - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info