Manual Pieps DSP Pro (page 19 of 103) (English, German, French, Italian, Spanish)

677798

Zoom out

Zoom in

1/103

ADDITIONAL FUNCTIONS FOR PIEPS DSP PRO

2. TRANSMIT PARAMETER CHECK

The transmit characteristics of an avalanche transceiver have to be in accordance with the

standard EN300718. The most important parameters are frequency, pulse length, period length.

Parameters outside of the allowed range may result in a serious limitation when searching for

such a device!

While the group-check-function (see BEACON-CHECK|GROUP-CHECK) only checks the

existence of a transmit signal and its frequency, the PIEPS DSP PRO allows a comprehensive

check of the transmit parameters:

The function is active as long as the SCAN button is pressed. Release the SCAN button to exit

the function. After a countdown of three seconds, your PIEPS DSP PRO automatically turns into

the SEND mode. During the countdown, the function can be reactivated.

Note: Accurate measurement takes a little time!

Further transceivers should keep a minimum distance of 5m.

3 second countdown

Activation of the transmit parameter check:

1. Turn on your PIEPS DSP PRO

(Position SEND).

2. Wait until „CH“ appears on the display

(CH = CHECK).

3. Press and continue to hold the SCAN button.

Check mode More than one

transceiver within

receiving range!

Device is sending

within the accep-

table range.

Error: Device is not

sending within the

acceptable range.

Device is sending

with continuous

signal.

 RESULT

ADDITIONAL FUNCTIONS FOR PIEPS DSP PRO

3. FREQUENCY MEASUREMENT

Press the SCAN button for more than 3 seconds while in

the SEARCH-mode. The PIEPS DSP PRO uses the frequency

measurement to check the frequency of all other beacons. The

frequency of the strongest (closest) beacon is measured. The

deviation from the standardized frequency 457kHz is indicated.

The shown number is the deviation in Hz and the arrows indicates

+ (right) or – (left). The frequency measurement ends when the

button SCAN is not pressed any longer.

IMPORTANT! Check the transmitting frequency of your ski

partners regularly to ensure best performance. According the

standard EN300718 a beacon must transmit within the range of

457 kHz +/- 80 Hz. Ideal and reasonable technical operation will

have a maximum deviation of no more than +/- 30 Hz.

4. TX600-SUPPORT

The PIEPS TX600 is a mini-transmitter for dogs and equipment

that transmits at 456 kHz, which is out of the standard EN300718

(457 kHz +/- 80 Hz) and can be received with every PIEPS DSP PRO.

Hold the MARK and SCAN buttons simultaneously for 3 seconds

while in the SEARCH-mode. The PIEPS DSP PRO switches into

the TX600-mode (“TX”-indication on the display) and indicates

the direction and distance to the strongest TX600 signal. Also the

functions MARK, SCAN and frequency measurement are available

in TX600-mode. To activate the search according to the standard

EN300718 again, switch the PIEPS DSP PRO to the SEND-mode

and then back to the SEARCH-mode.

IMPORTANT! In the standard SEARCH-mode the PIEPS DSP

PRO does not indicate the TX600. Active search operations are never

inuenced. A detection of the TX600 without switching to a special

mode is only possible in immediate vicinity (<1 m).

Example:

the frequency of

the measured signal

is 457 kHz + 10 Hz

(=457.010 Hz)

DEENESFRITCZSKSIRUJP

06/15 ||

06/15 3736

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Pieps DSP Pro in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 5,19 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Pieps DSP Pro Manual

Product: