677798
17
Zoom out
Zoom in
Previous page
1/103
Next page
The optimized multiple burial search is based on a separation of signals via the digital
signal processor (DSP).
MULTIPLE BURIALS
If there are multiple burials, this is clearly indicated by the number of matchstick men.
By default, the PIEPS DSP PRO/DSP SPORT will automatically search for the strongest signal.

MARK without moving away from this point. This signal is now suppressed. Once a signal
has been successfully suppressed, an outline appears around the matchstick man.
The PIEPS DSP PRO/DSP SPORT will automatically search for the next strongest signal.
Now continue the search as described above, and repeat the procedures until all
transmitters are located. If there are no further signals within the receiving range the
display indicates “No Signal”.
(1)
(2)
(3)
(4)
(5)
DEENESFRITCZSKSIRUJP
Number of
possible marks:
Marking is possible within a range
of 5 m to the transmitting beacon.
Marking of a second transmitter is
possible after 3 seconds after marking
 
these requirements are not provided,
an alert signal sounds by pressing the
button „MARK“ again.
max. 5 transmitters,
3 are indicated on
the display
Mark reset of single suppressed signals: To reset the MARK function for single signals, press
the button MARK for 3 seconds.
Mark reset of all suppressed signals: To reset the MARK function switch your PIEPS DSP
PRO/DSP SPORT into SEND-mode and then back to SEARCH-mode. With the PIEPS DSP PRO
you also have the possibility to reset MARK with the following described SCAN-function. All
information from previously suppressed signals is now reset and you can start with MARK again.
Old device mode: Older analog transceivers are transmitting a weak continuous signal
additional to the digital pulse signal that can have an impact on the digital signal separation. In


these transmitters keep a distance of more than 1 m.
signal with continuous carrier
signal without continuous carrier
IMPORTANT!
The MARK function is subject to physical and technical limitations. This applies to all
transceivers with MARK function! In practice, one might observe performance-reducing limitations which
get intensied by overlapping signals. More information can be found on www.pieps.com.
MULTIPLE BURIALS
PIEPS provides with the PIEPS SAFETY SYSTEM (digital PIEPS beacon and electronic probe
PIEPS iPROBE) a technical 100% solution for multiple burials. By using a digital PIEPS
beacon in combination with the PIEPS iPROBE or iPROBE ONE someone can solve a multiple
burial without any performance-reducing limitations! See also chapter „iPROBE Support“.
06/15 ||
06/15 3332
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pieps DSP Pro at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pieps DSP Pro in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 5,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info