This function is used to enable or disable the warning signal emitted if a safety device is activated.
This function is used to display the room temperature or the time on the display.
Description of activityDisplay
Press key 6 for a few seconds. Use key 5 or 6 to scroll the menu that appears on the
display until the scrolling readout BUZZER ENABLE appears.
Conrm by pressing the SET key.
BUZZERENABLE
Use key 1 or 2 to select on the display the option ON to enable the buzzer or OFF to
disable.
Conrm by pressing the SET key.
ONMODE
BUZZER
After conrmation the scrolling readout “FUNCTION ENABLED” appears on the display
and the display then returns to its original status.
FUNCTIONENABLED
Description of activityDisplay
Press key 6 for a few seconds. Use key 5 or 6 to scroll the menu that appears on the
display until the scrolling readout MODE DISPLAY appears.
Conrm by pressing the SET key.
MODEDISPLAY
Use key 1 or 2 to select on the display the option TEMP (enabling room temperature
display) or HOURS (enabling timetable display).
Conrm by pressing the SET key.
HOURDISPLAY
After conrmation, the scrolling readout “FUNCTION ENABLED” appears on the display
and the display automatically returns to its initial status.
FUNCTIONENABLED
DT2010082-04
6.12 LIGhTING FOR ThE FIRST TIME
-Carefully read this “Instructions for installation, use and maintenance” in its entirety before lighting your stove for the rst time.
-Before lighting the stove for the rst time, check that the grate is properly placed and pushed towards the left.
-There will be odours when lighting the rst few times due to the evaporation of paints and oils used during the manufacturing process.
During this stage, air the room well where the stove is installed and avoid staying there any length of time since the fumes being given off could be
harmful to persons or pets.
The stove body should have settled down and the paints fully evaporated after having lit the stove a few times.
To this end, follow the instructions given below when using the stove.
-Operate at medium power for the rst 5-6 hours after igniting the fuel (the expansion caused by the heat during this stage will allow the stove body
to settle).
-After the settling-down stage the stove must be set to operate at maximum power for a period between 6 and 10 hours, depending on the amount
of paint on the stove body that must be evaporated off.
The time indicated for operation at maximum power does not necessarily have to be continuous, but may be divided up into two periods separated by
an interval of at least 3-4 hours with the stove shut down.
At the end of the recommended period the paint will have evaporated and the stove should be used at the suitable power for normal use.
If necessary the stove may be used for a further period at maximum power to ensure complete and nal disappearance of all paint residue.
When the hopper is being loaded for the rst time the loading auger needs time to ll up; during this stage the pellets are not distributed inside the
rebox and it is highly probable that the rst attempt at ignition fails. If the alarm is activated, shut down the stove by pressing the ON/OFF key for a
few moments, remove the fuel in the grate and then set the stove for a new ignition process.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Piazzetta SABRINA at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Piazzetta SABRINA in the language / languages: English as an attachment in your email.
The manual is 2,92 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
