663513
14
Zoom out
Zoom in
Previous page
1/31
Next page
12
English
Setting up the surround sound
system
You must connect all the speakers and set up the system
properly in order to enjoy the Digital Cinema experience at
home (refer to “Connections - Connecting the speakers”).
You will have the feeling of being in the middle of the action
because sound is coming from everywhere around you.
The subwoofer can enhance the bass performance of your
system dramatically.
IMPORTANT!
Please sit at your usual listening position in order
to set up the speaker balance correctly.
Placing the speakers
To obtain the best surround effect, place the speakers as
follows.
1 Place the front left and right speakers at equal distances
from the TV and at an angle of approximately 45 degrees
from the listening position.
2 Place the centre speaker above or below the TV so the
centre channel’s sound is localised.
3 Place the surround speakers at normal listening ear level
facing each other or mounted on the wall.
4 Place the subwoofer on the floor near the TV.
Notes:
To avoid magnetic interference, do not position the front
speakers too close to your TV.
If the rear surround speakers are installed farther away
from the listening position than the front and centre speakers,
it will weaken the surround effect.
All speakers should be securely installed to prevent
accidents and improve sound quality.
Changing the volume level
You can change the speakers’ sound distribution to suit
your surround sound needs, except for CDDA DTS disc.
Press CENTER +/- to adjust the level of the centre
speaker.
CEN XX is displayed.
Press REAR +/- to adjust the level of the rear
surround speakers.
SL XX or “SR XX is displayed.
Notes:
–“XX denotes the volume level between -6 to +6.
For CDDA DTS disc, please refer to “System Setup (DVD) -
Setting the sound ( ) - Speakers” for changing the volume
level of the centre speaker, rear speakers and subwoofer.
Setting up the subwoofer
1 Use the supplied subwoofer cable to connect the
subwoofer’s audio input jack to the WOOFER LINE
OUT jack of the DVD system.
2 Connect the subwoofer’s AC power cable to the wall
socket and switch on the power.
It will automatically switch on when receiving an audio
signal input. If there is no audio signal input, it will switch off
automatically.
3 Set the phase polarity at the rear of the subwoofer at
either 0
o
or 180
o
to determine better bass reproduction
effect in your listening environment.
4 Press SUBW +/- to adjust the volume level of the
subwoofer (-6 to +6).
SUB XX is displayed.
Inserting batteries into the
remote control
1 Open the battery compartment.
2 Place the batteries in the
compartment with the correct
polarity as indicated by +“ and -
symbols.
3 Close the cover.
CAUTION!
Remove batteries if they are exhausted or will
not be used for a long time.
Do not use old and new or different types of
batteries in combination.
Batteries contain chemical substances, so they
should be disposed off properly.
Preparations
PREPARATIONS
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Philips LX8000SA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Philips LX8000SA in the language / languages: English as an attachment in your email.

The manual is 0,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Philips LX8000SA

Philips LX8000SA User Manual - Dutch - 31 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info