Manual Philips FT565 (page 5 of 44) (English, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian, Finnish)

799038

Zoom out

Zoom in

1/44

transmitters. In the case of very powerful

medium wave transmitters the indicator may

light up on several consecutive tuning frequen-

cies.

(u) 'STEREO' indicator

This lights up if the tuned transmitter is received

in stereo.

@ 'MEMORY' button

Button for starting the programming procedure.

If this button is pressed, then it is possible to

programme the pre-selected transmitter for

5 seconde. During the programming procedure

the tuner is in memory mode, indicated by the

lighting up of the word 'MEMORY' on display (f).

@ 'LW' selector button

For selecting the long wave tuning range.

When this button is pressed, the 'LW' indicator

lights up on display ®.

@ 'MW' selector button

For selecting the medium wave tuning range.

When this button is pressed, the 'MW' indicator

lights up on display @.

@ 'FM' selector button

For selecting the 'FM' tuning range.

When this button is pressed, the 'FM' indicator

lights up on display @.

OPERATION

The tuner may be operated directly or via remote

control.

In both cases the amplifier must first be switched

on.

Operating via remote control

This is only possible with preprogrammed stations.

Programming can not be done with the aid of the

remote control, but only directly from the tuner.

You should therefore first programme the tuner and

then read the instructions for operating the tuner in

the booklet supplied with the remote control.

With the amplifier switched on and set to tuner

playback (the 'TUNER' indicator is lit up!) the

transmitters can be tuned as follows:

1. Switch the tuner on by pressing 'ON/OFF'

switch 0. The tuner then returns automatically

to the last position it was in before it was

switched off.

2. Select LW, MW or FM by pressing 'LW' button

@, 'MW' @ or 'FM' @.

In the 'LW' position indicators 'LW' and 'kHz'

light up on display (s).

In the 'MW' position indicators 'MW' and 'kHz'

light up on display (s).

In the 'FM' position indicators 'FM' and 'MHz'

light up on display ®.

3. Three different ways can then be used con-

secutively to tune to the required transmitter,

i.e. automatic tuning, manual tuning and tuning

on pre-selected transmitters.

A. Automatic tuning

• By pressing button ® 'DOWN' or @ 'UP' once

andforlongerthan 0.5 second, the selected tuning

range is searched step by step until the tuner

locates a transmitter of adequate strength, at which

it stops. Indicator @ 'TUNED' lights up. If it is a

stereo transmission, indicator @ 'STEREO' lights

up.

• If the station selected is not the one you want,

press button ® or @ again. Automatic tuning is

then resumed, until another station is located.

Wofe; If the end of a tuning range is reached, tuning

stops and begins again from the other end of the

tuning range.

• Depress, if desired, key @ 'FM-NR' to reduce

possible noise.

• During tuning the audio signals are completely

suppressed, in order to prevent any interference

from parasitic noise.

Note:

Relatively weak transmitters are passed over

during automatic tuning and can only be selected

with manual tuning.

Tuner does not search

- The frequency has only changed by one step and

you have not pressed button @ or (D for long

enough.

The tuner locates few stations

- The aerial signals received are too weak.

- Check the aerial connections.

- Adjust the position of the AM frame or the FM

indoor aerial.

If this does not give satisfactory results, the

transmitters received are too weak,

In this case consider connection to external

aerials or cable network.

- If these are already fitted, check their connection

to the tuner.

B. IVIanual tuning

• To help prevent poorly tuned transmitters being

stored in the memory, it is useful to know the exact

tuning frequency of the transmitters received in the

area.

For this Information consult a programme

magazine.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Philips FT565 in the language / languages: English, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 15.68 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Philips FT565 Manual

Product: