301428
81
Zoom out
Zoom in
Previous page
1/88
Next page
ErgoLine D310/320
Customer Engineer Manual
Page 5-
7
Cable and Distances
The S
0
interface consists of two balanced twisted pairs, one pair for Transmit and
one pair for Receive. The distance between the ErgoLine and the Switch depends
upon the configuration and the cable characteristics of the cable used between
the wall socket and the Main Distribution Frame (MDF).
The U
PN
interface consists of one balanced twisted pair with half duplex operation
being used. The cable length is defined by cable type.
CHARACTERISTICS
S
0
SPECIFICATION U
PN
SPECIFICATION
Cable impedance
100
at 96kHz
100
at 192kHz
Wire diameter 0.5mm 0.5mm
Loop attenuation < 10dB / km at 96kHz
26dB / km at 192kHz
Round trip delay
< 1
µ
sec / 100m max 23
µ
sec (total)
ErgoLine line cord length < 10m (normally 6m) 6m
ErgoLine line cord
connector
8 pin RJ45 according to
ISO 8877
8 pin RJ45 according to
ISO 8877
T
ABLE
5.1. T
YPICAL
C
ABLE
C
HARACTERISTICS
For the possible wiring configurations, see the chapter “Cables and Distances” on
page 2-4 of the ErgoLine D330/D340 section of this manual. Note however that
the ErgoLine D310 and D320 cannot be connected to a DLC-C or DLC-D via a
PNT1.
Both twisted pairs must be terminated (preferable in the wall socket) with a 100
resistor.
Note 1
: When using a cable with cable characteristics different from the
ones listed in Table 5.1, the lengths of cable required will be different.
Note 2
: An intermediate MDF in the connection can also affect the overall
cable characteristics.
Note 3
: When cables are connected together additional attenuation,
caused by the joints, will occur.
When an ErgoLine D310 or D320 terminal is connected via a PNT1 to a DLC-U, the
distance can be extended by 1500 m. In this case the attenuation of the cable
used between the PNT1 and DLC may not exceed 15dB (at 100kHz, without noise
insertion).
Any combination of two ErgoLine models (D310, D320, D330 or D340) can be co-
located. This means that different models (e.g. a D320 and a D340) may be
connected to the same S0 bus. They are identified by TEI or EAZ.
Connecting the ErgoLine Terminal
Connect the D310/D320 as follows:
connect the handset into the handset port, and put the handset on the
cradle
plug in the telephone line cord at the wall socket or the PNT1
81


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Philips ergoline d340 2 dg at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Philips ergoline d340 2 dg in the language / languages: English as an attachment in your email.

The manual is 2,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Philips ergoline d340 2 dg

Philips ergoline d340 2 dg User Manual - Dutch - 99 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info