782694
6
Zoom out
Zoom in
Previous page
1/23
Next page
8.4.2 Repeatedly press the '4 WAY' button to select the required access options from:
'IN & OUT', 'IN ONLY', 'OUT ONLY', 'LOCKED' or 'OFF'.
8.4.3 Press the 'PROG' button to save the setting.
8.4.4 The display will show time with the Minute symbol flashing. Repeatedly press
the '+' button until the current Minutes setting is shown (i.e. 10 if the current time
is 12:10).
8.4.5 Press the 'PROG' button to save the setting.
8.4.6 The display will now show the time with the Hour symbol flashing.
If you wish to change between a 24 hour clock and AM/PM setting, press the
'TIMER' button.
8.4.7 Repeatedly press the '+' until the correct Hour setting is shown (e.g. 12 if the
current time is 12:10).
8.4.8 Press the 'PROG' button to save the setting.
8.4.9 The display will show the word 'START' and the minutes will flash. Press the
'+' button until the desired minutes setting is shown, (in the above example
'00'). Press the 'PROG' button to save the setting.
8.4.10 Then set the hours in the same way (in the above example 19:00).
8.4.11 The display will show the 'FINISH' time. Set in the same way as the 'START'
time. Remember to press 'PROG' to save the setting.
When the Timer is set, the Timer function indicator ( 5 , Fig. 1) will be shown on the
display.
When the timed lock is active, the access option symbol chosen at 8.2 will flash slowly.
To check the time settings, briefly press the 'TIMER' button and release. The display
will show the timed access option selected and the 'START' time. Press the 'TIMER'
button again to show 'FINISH' time. The display will revert to current time after 5
seconds.
To cancel timer control and revert back to the normal access option:
8.4.12 Press the 'TIMER' button for 5 seconds.
8.4.13 Press the '4 WAY' button and go back through the options until you come to
'OFF'.
8.4.14 Press the 'PROG' button 3 times to keep the current clock time and return to
the normal display.
9. Battery Replacement
When the low battery indicator ( 3 , Fig. 1) comes on, alkaline batteries should be
replaced. (See Section 2).
Please note, after fitting new batteries:
Low battery indicator may remain on for up to 15 minutes.
Flap will remember all microchip(s) and I.D. Disc(s), Lock Settings and Lock Times
but CURRENT TIME WILL NEED RESETTING. (See section 8.4).
7. To View How Long Since the Cat(s) Last Used the Cat Flap
7.1 To view how many hours
and minutes
since cats 1, 2 or 3 last used the cat flap,
press the '+' button.
7.2 The display will show the symbol for 'CAT 1' and how many hours
and minutes
ago 'CAT 1' used the flap up to a maximum of 99 hours.
7.3 Press '+' again for similar information on Cats 2 and 3.
7.4 Press '+' a fourth time (or leave for 20 seconds) and the normal display will be
resumed.
8. Access Options
The access options available are shown below.
'In & Out' Your cat(s) can come in and out of the flap
'In Only' Your cat(s) can come in through the flap but cannot leave through
the flap
'Out Only' Cat(s) can go out through the flap but cannot enter through the flap
'Locked' Cat(s) cannot use the flap
Select an access option as follows:
8.1 Press and hold the '4 WAY' button for 5 seconds until the display flashes.
8.2 Repeatedly press the '4 WAY' button to scroll through the available access
options, until you come to the one you want.
8.3 Press the 'PROG' button to save the setting.
8.4 Setting Timer Control/Clock for ALL Cats
If you wish to set your cat flap to ensure that ALL cats have a particular access option,
over a selected timed period, e.g. to keep your cat(s) in at night between 19:00 and
06:00, you will first need to decide:
a) Which lock setting should apply DURING the timed period, (in the above example
'IN ONLY' will apply). Outside the timed period, the lock setting made in 8.1 to 8.3
will apply.
b) When the timed period should 'START' (In the above example 19:00hrs).
c) When the timed period should 'FINISH' (in the above example 06:00hrs).
d) You will also need to know the current time.
Proceed as follows:
NOTE: if you do not press a button for more than 60 seconds the display will revert to
normal and you will need to start again.
8.4.1 Press the 'TIMER' button for 5 seconds until the Timer function indicator
flashes. 10 11
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pet-Mate Cat-Mate Elite 355 Cat flap at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pet-Mate Cat-Mate Elite 355 Cat flap in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 1.3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info