782694

Pet-Mate Cat-Mate Elite 355 Cat flap Manual

5
Zoom out
Zoom in
Previous page
1/23
Next page
4.4.3 Remove interior frame cover by unscrewing 2 screws in rear of interior frame (Fig.
13).
(Note: these screws may be discarded as it will be impossible to refit them).
Next remove the outermost 2 screws under the battery cover and remove the
interior frame by pivoting down (Fig. 14).
4.4.4 Carefully remove 2 screw clips with pliers. (Fig. 15).
4.4.5 Fit interior frame assembled with requisite number of wall liners to interior wall
securing in position with 2 suitable screws as shown in Fig. 16.
(Note: you will
need to fit a washer (not supplied) under the head of the screws).
If required, the
wall liners may be glued in place, although a firm push fit will usually suffice.
4.4.6 Refit interior frame cover with 2 screws under battery cover, taking great care not
to trap electrical wires. Replace the battery cover.
4.4.7 Fit exterior frame using 2 off 25mm (1") screws supplied and finally, fit 2 screw
caps.
5. Training Your Cat to Use the Cat Flap (or if Your Cat Has Lost its I.D. Disc)
It may take a little time for your cat to get used to its new cat flap. To help your cat get
used to entering and exiting the flap, the flap can be set to 'TRAINING MODE' by
pressing and holding the 'PROG' button and within 3 seconds briefly pressing the '4
WAY' button.
After 5 seconds the lock will unlock and the 'PROG' button should then be released.
The 'IN & OUT' symbol will remain flashing.
Please be aware that in 'TRAINING MODE' your cat flap will allow access for other
animals.
To exit the 'TRAINING MODE', press and hold the 'PROG' button and within
3 seconds briefly press the '4 WAY' button. After 5 seconds the flap will re-lock and
the 'PROG' button should then be released.
For very hesitant cats, whilst in the 'TRAINING MODE', use food to encourage the cat
to enter and exit the flap.
NOTE: We do NOT recommend that cats, particularly kittens, are left alone to use
their cat flap until you are satisfied that they are completely familiar with its operation.
6. Viewing Your Cat’s Location
The LCD shows at a glance, the location of up to three cats (1-3).
The cat last went through the The cat last went through the
flap, coming into the house. flap, going out of the house.
Please note this display is only a guide to your cats' location. The cat flap determines
the location of your cat by recording its last movement through the cat flap.
The results may be misleading if the cat has an alternative entrance/exit to the house
or if the cat has followed another cat through the cat flap; if it only puts its nose out of
the cat flap etc.
4.2 UPVC / Metal Doors 0-50mm (0-2”) Thick
Doors constructed with metal panels may reduce the range of the microchip reader. You
may test for metal panels by drilling a small trial hole in the middle of the intended cat
flap location.
For UPVC / metal doors it is essential to cut a larger hole than for wooden doors
and to retune the cat flap as below:
4.2.1 Place exterior frame in desired position on door. We recommend the bottom of the
aperture is approximately 150mm (6") above ground level. (Fig. 9a). If you must
fit higher consider providing a step to help your cat enter.
4.2.2 Draw around the OUTSIDE of the frame. (Fig. 9a). Using an electric jigsaw cut
12mm (1/2") INSIDE the line (Fig. 9b).
4.2.3 Determine thickness of door panel, (t). (Fig. 10).
4.2.4 Position interior frame on inside of door and screw exterior frame to it by using
appropriate screws for panel thickness, (t), as shown in Fig. 12. If necessary, cut
supplied screws to length. DO NOT OVERTIGHTEN SCREWS which may
prevent the flap from closing properly - use a manual screwdriver. Finally fit two
screw caps.
4.2.5 Remove batteries for a minimum of 2 minutes after installation. This will enable
the cat flap to retune itself to its new location.
4.3 Glass Panels
4.3.1 We recommend that you ask a glazier to cut a hole of 232mm (91/8") diameter in
the position required and then install the cat flap as detailed below. Alternatively,
you may prefer to replace the glass panel with a clear plastic panel and install as
instructions 4.1.1 to 4.1.6.
Note: It is not possible to cut a hole in double glazed or toughened glass. You will
need a new glass panel with the hole already cut from your glazier.
4.3.2 Determine thickness of panel, (t). (Fig. 10).
4.3.3 The black foam seal is not suitable for fitting to glass and should be removed. If
desired, the exterior frame may be sealed to the glass panel using silicone
sealant.
4.3.4 Position interior frame on inside of panel, screw exterior frame to it by using
appropriate screws for panel thickness, (t), as shown in Fig. 12. If necessary, cut
supplied screws to length. DO NOT OVERTIGHTEN SCREWS which may
prevent the flap from closing properly - use a manual screw driver. Finally fit two
screw caps.
4.4 Wall Fitting
If you are installing your cat flap in a wall, you will need to purchase Cat Mate Elite Wall
Liners. You will need 1 wall liner for every 50mm (2") of wall thickness over 100mm (4").
4.4.1 Create a rectangular hole in your wall 205mm (8") high by 180mm (7") wide.
4.4.2 Remove interior frame battery cover by pushing up as shown (Fig. 2).
8 9
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pet-Mate Cat-Mate Elite 355 Cat flap at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pet-Mate Cat-Mate Elite 355 Cat flap in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 1.3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info