518739

Partner P340S Manual

9
Zoom out
Zoom in
Previous page
1/282
Next page
-- 8 --
1. Fill the fuel tank (A) with correct fuel
mixture. (Fig. 8).
2. Fill the oil tank (B) with correct chain and
bar oil (Fig. 8).
3. Be certain the chain brake is disengaged
(C) before starting unit (Fig. 8).
1. Make sure the on/off switch is in the “I”
position.
2. Depress the primer bulb 10 times.
3. Pull the starter rope rapidly 4
times. The engine should start.
4. If the engine still can not start, follow the
step as “To start engine” in this user
manual.
1. Release trigger and allow engine to
return to idle speed.
2. Press STOP switch down to stop engine
Figure 9G.
NOTE: For emergency stopping, simply
activate CHAIN BRAKE and move
STOP switch down.
1. Place saw on a clear, firm, flat surface.
2. Start engine.
3. Grasp the rear handle (A) with your right
hand (Fig. 10).
4. With your left hand, hold the front
handle (B) [not CHAIN BRAKElever (C)]
firmly (Fig. 10).
5. Squeeze the throttle trigger to 1/3 throttle,
then immediately activate the
CHAIN
BRAKElever (C) (Fig. 10).
6. Chain should stop abruptly. When it does,
immediately release the throttle trigger.
7. If chain brake functions properly, turn the
engine off
and return the chain brake to
the DISENGAGED position.
Test the CHAIN BRAKE periodically to
ensure proper function.
Perform a CHAIN BRAKE test prior to initial
cutting, following extensive cutting, and
definitely following any CHAIN BRAKE
service.
1. Move ON/OFF switch to ON “I”
position. (Fig. 9A)
2. Pull choke lever/throttle (A) advance.This
sets choke and advances throttle for
easier starting. (Fig. 9B)
3. Press primer bulb (B) 10 times. (Fig. 9C)
4. With saw on ground, grip front handle
firmly with left hand and place right foot
inside rear handle. Pull starter rope 4
times with right hand. (Fig. 9D)
NOTE: If the engine sounds as if it wants
to start before the 4th pull, end the tugging
of the starter and proceed as described in
the next step.
5. Push choke lever (C) in
completely. (Fig. 9E)
6. Pull starter rope quickly until engine
starts.
7. Allow the engine to run for about 10
seconds. Squeeze and release throttle
trigger (D) to idle engine.
(Fig. 9F)
8. If the eingine does not start up, repeat
the above steps.
OPERATION
ENGINE PRE-START CHECKS
WARNING: Never start or operate
the saw unless the bar and chain are
properlyinstalled.
WARNING: Activate the chain brake
slowly and deliberately. Keep the chain
from touching anything; don t let the saw tip
forward.
WARNING: If chain does not
stop, turn engine off and take your unit to
the nearest Authorized Service Center for
service.
Fig. 8
B
A
C
TO START ENGINE
Fig. 9A Fig. 9B
A
Fig. 9C Fig. 9D
B
Fig. 9E Fig. 9F
D
C
RE-STARTING A WARM ENGINE
TO STOP ENGINE
Fig. 9G
CHAIN BRAKE OPERATIONAL TEST
TEST CHAIN BRAKEAS FOLLOWS:
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Partner P340S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Partner P340S in the language / languages: English, German, Danish, Polish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 6,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info