518739

Partner P340S Manual

8
Zoom out
Zoom in
Previous page
1/282
Next page
-- 7 --
FUEL AND LUBRICATION
WARNING: The purpose of the
chain brake is to reduce the possibility of
injury due to kickback; however, it cannot
provide the intended measure of protection
if the saw is operated carelessly. Always
test the chain brake before using your saw
and periodically while on the job.
Your chain saw is equipped with a Chain
brake that reduces possibility of injury due to
kickback. The brake is activated if pressure
is applied against brake lever when, as in
the event of kickback, operator’s hand
strikes the lever. When the brake is actuated,
chain movement stops abruptly.
WARNING: Never use straight
gasoline in your unit. This will cause
permanent engine damage and void the
manufacturer’s warranty for that product.
Never use a fuel mixture that has been
stored for over 90 days.
Use regular grade unleaded gasoline
mixed with 40:1 custom 2-cycle engine oil
for best results. Use mixing ratios in Section
FUEL MIXINGTABLE.
Some conventional petrols are being
blended with oxygenates such as alcohol or
an ether compound to meet clean air
standards.Your engine is designed to operate
satisfactorily on any gasoline intended for
automotive use including oxygenated
petrols.
Always refill the chain oil tank each time the
fuel tank is refilled. We recommend using
Partner Chain, Bar and Sprocket Oil, which
contains additives to reduce friction and
wear and to assist in the prevention of pitch
formation on the bar and chain.
Mix fuel with 2 cycle oil in an approved
container. Use mixing table for correct
ratio of fuel to oil. Shake container to
ensure thorough mix.
WARNING: Lack of lubrication voids
engine warranty.
WARNING: If 2-cycle lubricant
other than Custom Lubricant is to be used, it
must be a premium grade oil for 2-cycle air
cooled engines mixed at a 40:1 ratio. Do not
use any 2-cycle oil product with a
recommended mixing ratio of 100:1. If
insufficient lubrication is the cause of engine
damage, it voids the manufacturer’s engine
warranty for that occurrence.
1. The CHAIN BRAKE is DISENGAGED
(chain can move) when BRAKE LEVER
IS PULLED BACK AND LOCKED. Be
sure the chain brake latch is in the OFF
position. (Fig. 7A)
CHAIN BRAKE MECHANICAL TEST
TO TEST CHAIN BRAKE:
2. The CHAIN BRAKEis ENGAGED (chain
is stopped) when brake lever is in forward
position and the chain brake latch is in
the ON position. You should not be able
to move chain. (Fig. 7B)
NOTE:The brake lever should snap into both
positions. If strong resistance is felt, or lever
does not move into either position, do not use
your saw. Take it immediately to a
professional Service Center for repair.
Fig. 7A Fig. 7B
OFF
ON
FUEL
MIXING FUEL
FUEL AND LUBRICATION
Gasoline and Oil
Mix 40:1
Oil Only
FUEL MIXING TABLE
RECOMMENDED FUELS
CHAIN AND BAR LUBRICATION
GASOLINE 40:1 Ratio
Custom Lubricant
1 U.S. Gal. 3.2 oz. 95ml (cc)
5 Liters 4.3 oz. 125ml (cc)
4.3 oz. 125ml (cc)
1 lmp. Gal.
Mixing 40 Parts Gasoline
Procedure to 1 part Lubricant
1ml = 1cc
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Partner P340S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Partner P340S in the language / languages: English, German, Danish, Polish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 6,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info