706364

Parkside PZKS 1500 B2 - IAN 295934 Manual

104
Zoom out
Zoom in
Previous page
1/110
Next page
99GB / IE / NI
• Cut as described under section 8.5.
8.7 Precision adjustment of the
stop for bevel cut 45° (Fig.
1/12/13)
• No stop angle included.
• Lower the machine head (4) and secure
using the fastening bolt (30).
• Fix the turntable (15) in the 0° position.
• Loosen the locking screw (27) and use
the handle (1) to angle the machine head
(4) 45° to the left.
• Place the 45° - position angle stop (b)
between the saw blade (6) and turntable
(15).
• Release the locking nut (c) and adjust
the adjusting screw (34) until the angle
between the saw blade (6) and turntable
(15) is precisely 45°.
• Re-tighten the locking nut (c).
• Subsequently check the position of the
angle indicator.
If necessary loosen the bevel angle
pointer (24) using a Philips screwdriver,
set to position 45° on the bevel angle
scale (23) and re-tighten the retaining
screw.
8.8 Bevel cut 0°- 45° and mitre
cut 0° (Fig. 1/2/14)
The crosscut saw can be used to make bevel
cuts of 0° - 45° in relation to the work face.
• Move the machine head (4) to the top
position.
• Fix the turntable (15) in the 0° position.
• Loosen the locking screw (27) and use
the handle (1) to angle the machine
head (4) to the left, until the bevel angle
pointer (24) indicates the desired angle
measurement on the bevel angle scale
(23).
• Re-tighten the locking screw (27)
• Cut as described in section 8.5.
8.9 Bevel cut 0°- 45° and mitre
cut 0°- 45° (Fig. 1/2/15)
The crosscut saw can be used to make bevel
cuts to the left of 0°- 45° in relation to the
work face and, at the same time, 0° - 45° to
the left or 0° - 45° to the right in relation to
the stop rail (double mitre cut).
• Move the machine head (4) to its upper
position.
• Loosening the metre lock handle (10) and
press the metre detent lever (11).
• Using the mitre locking handle (10), set
the turntable (15) to the desired angle
(refer also to point 8.6 in this regard).
• Re-tighten the mitre lock handle (10) in
order to secure the rotary table.
• Loosen the locking screw (27) and use
the handle (1) to tilt the machine head
(4) to the left until it coincides with the
required angle value (in this connection
see also section 8.8).
• Re-tighten the locking screw (27)
.
• Cut as described under section 8.5.
8.10 Limiting the cutting depth
(Fig. 1/16)
• The cutting depth can be infinitely
adjusted using the screw (19). To do this
loosen the knurled nut on the screw (19).
Move the stop for the cutting depth limitre
(18) to the outside. Turn the screw (19) in
or out to set the required cutting depth.
Then re-tighten the knurled nut on the
screw (19).
• Check the setting by completing a test
cut.
8.11 Sawdust bag (Fig. 1)
Dust/Chip Extraction
Dust from materials such as lead-containing
Attachment and operation
… 104 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PZKS 1500 B2 - IAN 295934 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PZKS 1500 B2 - IAN 295934 in the language / languages: English, German, Dutch, Danish, French as an attachment in your email.

The manual is 2,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info