Manual Parkside PZKS 1500 B2 - IAN 295934 (page 102 of 110) (English, German, Dutch, Danish, French)

706364

102

Zoom out

Zoom in

1/110

97GB / IE / NI

- Attach the miter lock handle (10) to the

turntable (15).

- When fixing the saw to the workbench,

insert the mounting screws (not included)

through the mounting holes (16a).

• In order to adjust the turntable (15)

loosen the mitre lock handle (10) approx.

2 turns.

• Press the mitre detent lever (11) and turn

the turntable (15) and pointer (12) to the

desired angle measurement on the scale

(14), release the mitre detent lever (11)

and secure with the mitre lock handle

(10).

• Pressing the machine head (4) lightly

downwards and removing the fastening

bolt (30) from the motor bracket at the

same time disengages the saw from the

lowest position.

• Swing the machine head (4) up until the

release lever (3) latches into place.

• It is possible to secure the clamping

device (7) to the left or right on the

stationary saw bench. Insert the clamping

device (7) in the hole on the rear side of

the stop rail (17) and secure it with the

grip screw (28).

• Attach the workpiece supports (8) to the

fixed saw table (16) as shown in Figure

5 and fasten with the screw (29).

• It is possible to tilt the machine head (4)

a max. 45° to the left by loosening the

locking screw (27).

8.2 Mitre angle setting

• Nine positive miter detents are provided

for fast and accurate preset miter angles

– locations are at 45°, 30°, 22.5°, 15°

left and right, and center at 0°.

• Follow the process for mitre angle setting.

• Unlock the turntable by turning the mitre

lock handle (10) counter-clockwise.

• Move the turntable while press the mitre

detent lever (11) to align the mitre angle

pointer (12) to the desired degree on the

mitre angle scale (14).

• If the desired angle is one of the nine

positive mitre detents, release the mitre

detent lever (11), making sure the lever

snaps into position, and then secure by

tightening the mitre lock handle (10).

• If the mitre angle desired is not one of the

nine positive mitre detents, simply lock

the turntable into desired angle position

by turning the mitre lock handle (10) in

the clockwise direction.

8.3 Precision adjustment of the

blade for crosscut 90°

(Fig. 1/2/6/7)

• No stop angle included.

• Move the head (4) in position, so that

the blade (6) rests directly above the

turntable (15). Now, use locking screw

(25) to lock the drag guide (26).

• Lower the machine head (4) and secure

using the fastening bolt (30).

• Loosen the bevel locking screw (27).

• Position the angle stop (a) between the

saw blade (6) and the turntable (15).

• Release the locking nut (c) and adjust

the adjusting screw (32) until the angle

between the saw blade (6) and turntable

(15) is 90°.

• Re-tighten the locking nut (c).

• Subsequently check the position of the

angle indicator. If necessary loosen the

pointer (24) using a Philips screwdriver,

set to position 0° on the angle scale (23)

and re-tighten the retaining screw.

8.4 Precision adjustment of stop

rail for crosscut 90°

(Fig. 1/8/9)

- Bring the power tool into the working

position.

- Turn the turntable (15) to the 0° on the

mitre angle scale (14). The metre detent

lever

（

）

must be felt to engage in

the detent.

Attachment and operation

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PZKS 1500 B2 - IAN 295934 in the language / languages: English, German, Dutch, Danish, French as an attachment in your email.

The manual is 2,53 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside PZKS 1500 B2 - IAN 295934 Manual

Product: