722852

Parkside PWSAP 20-L i A1 - IAN 289752 Manual

31
Zoom out
Zoom in
Previous page
1/114
Next page
Q Operation
CAUTION! RISK OF INJURY!
u Keep your hands away from the accessory
when the product is in operation.
Q Switching on and off
This power tool is to be switched on in two steps.
Switching on:
1. Push the rear part of the on / off
switch
12
down and slide it forward.
For continuous activation, now tilt the front
part downwards until it engages.
Switching off:
1. Press the rear part of the on / off switch
12
so that it snaps back into its off-position to
switch the product off.
Q Trial run
NOTE
u Always carry out a trial run before carrying
out your first grinding procedure and after
every accessory replacement. Switch the
product off immediately if the accessory is not
rotating smoothly, if considerable vibration
occurs or if you hear abnormal noises.
Q Grinding
WARNING!
u Never use a cutting disc for grinding!
1. Hold the product at a 10° to 15° angle for
easy handling and smooth grinding results.
2. Apply the grinding disc to the work surface
with a light, steady pressure for maximum
grinding efficiency. It should never be
necessary to force the product. The weight of
the product applies adequate pressure.
3. Excessive pressure will overload the motor,
slow the grinding action, put dangerous stress
on the grinding disc and causes breakage.
4. Move the product back and forth steadily.
Q Wire brushing
WARNING!
u Do not use brush that is damaged, or which
is out of balance. Use of damaged brush
could increase potential for injury from
contact with broken brush wires.
1. Avoid applying too much pressure which
causes over bending of wires, leading to
premature breakage.
2. Work with moderate feed, suited to the
material being worked.
3. Avoid bouncing and snagging the wire brush,
especially when working corners, sharp edges
etc. This can cause loss of control and kick-back.
Q After use
1. Switch the product off, remove the battery
pack
4
and let it cool down.
2. Check, clean and store the product as
described below.
Q Cleaning and care
WARNING!
Always switch the product off, remove
the battery pack and let the product
cool down before performing inspection,
maintenance and cleaning work!
Q Cleaning
o The product must always be kept clean, dry
and free from oil or grease. Remove debris
from it after each use and before storage.
o Regular and proper cleaning will help ensure
safe use and prolong the life of the product.
o Inspect the product before each use for worn
and damaged parts. Do not operate it if you
find broken and worn parts.
o Never allow fluids to get into the product.
o Clean the product with a dry cloth. Use a
brush for areas that are hard to reach.
o In particular clean the air vents after every
use with a cloth and brush.
o Remove stubborn dirt with high pressure air
(max. 3 bar).
NOTE
u Do not use chemical, alkaline, abrasive or
other aggressive detergents or disinfectants
to clean this product as they might be harmful
to its surfaces.
33 GB / IE
289752_CB8_DE_EN_FR_NL_CS_ES_PT_170930.indb 33 9/30/17 8:11 AM
… 31 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PWSAP 20-L i A1 - IAN 289752 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PWSAP 20-L i A1 - IAN 289752 in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 4,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PWSAP 20-L i A1 - IAN 289752

Parkside PWSAP 20-L i A1 - IAN 289752 Additional guide - English, German, Dutch, French, Portuguese, Spanish - 73 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info