576693
14
Zoom out
Zoom in
Previous page
1/91
Next page
11
PWS 125 A1
GB
IE
Place the rough grinding or cutting disc on the
mounting fl ange with the label side towards
the appliance.
Then replace the tensioning nut
on the mount-
ing spindle
with the raised side facing up.
Press the spindle locking button
to lock the
mechanism.
Tighten the tensioning nut
using the span-
ner
.
NOTE
If the disc does not turn smoothly or vibrates
after the change, the disc must immediately
be replaced.
For safety’s sake, run at high idle for 60
seconds after every disc change. Be aware of
unusual noises and sparks.
Check whether all the fastening elements are
correctly fi tted.
Make sure that the arrow showing the direction
of rotation (if any) on the cutting or rough grind-
ing discs (including diamond cutting discs) and
the direction of rotation of the appliance (arrow
showing the direction of rotation on the head)
match.
General information about the
supplied grinding tool
Grinding tools are very fragile. Extreme care is
required when handling grinding tools.
Check grinding tools and brushes for damage
prior to initial use. Do not use damaged, incor-
rectly clamped or incorrecty installed grinding
tools.
Follow the safety instructions on the grinding
tools as well as the restrictions on use or safety
instructions.
Storage and handling
Grinding tools are to be treated with care and
transported carefully.
Grinding tools should be stored in such a way
that they are not exposed to mechanical da-
mage or environmental infl uences (e.g. moisture).
Before using the grinder
You should subject grinding tools to a visual
inspection before each use.
Do not use grinding tools if they are damaged
or if the expiration date has elapsed.
Using accessories
Cutting/rough grinding discs
You can use the following cutting/rough grinding
discs on this appliance:
Dimensions: ø 125 x 22.2mm to
max. 6mm thick (off set)
Rotational speed: min. 12000 rpm
Circumferential speed: 80 m/sec
Flap buff er discs for metal
Dimensions: ø 125mm
Rotational speed: min. 12000 rpm
Additional accessories
You can also use the grinding tools below with the
following technical data:
Spindle thread: M14
Rotational speed: min. 12000 rpm
Support plate for
sanding sheets with
dimensions: ø 115mm/125mm
IB_102828_PWS125A1_LB3.indb 11 22.08.14 11:48
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PWS 125 A1 - IAN 102828 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PWS 125 A1 - IAN 102828 in the language / languages: English, German, Dutch, Danish, Swedish, Finnish as an attachment in your email.

The manual is 4,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info