Manual Parkside PTK 2000 A1 - IAN 104416 (page 15 of 64) (English, German, Dutch, French)

595333

Zoom out

Zoom in

1/64

10 GB

12 Keep batteries out of the reach of children.

13 Do not allow children to replace batteries without

supervision!

14 Do not keep batteries near re, ovens or other

sources of heat. Do not use batteries in direct sun-

light or store them in vehicles in hot weather.

15 Keep unused batteries in the original packaging and

keep them away from metal objects. Do not mix

unpacked batteries or toss them together! This can

lead to a short-circuit of the battery and thus dam-

age, burns or even the risk of re.

16 Remove batteries from the equipment when it will

not be used for an extended period of time, unless

it is for emergencies!

17 NEVER handle batteries that have leaked without

appropriate protection. If the leaked uid comes into

contact with your skin, the skin in this area should be

rinsed off under running water immediately. Always

prevent the uid from coming into contact with the

eyes and mouth. In the event of contact, please seek

immediate medical attention.

18 Clean the battery contacts and corresponding con-

tacts in the device prior to inserting the batteries:

Residual risks

The machine has been built according to the state of

the art and the recognised technical safety require-

ments. However, individual residual risks can arise

during operation.

• Health hazard due to electrical power, with the use of

improper electrical connection cables.

• Furthermore, despite all precautions having been met,

some non-obvious residual risks may still remain.

• Residual risks can be minimised if the „safety instruc-

tions“ and the „Proper use“ are observed along with

the whole of the operating instructions.

• Do not load the machine unnecessarily: excessive

pressure when sawing will quickly damage the saw

blade, which results in reduced output of the machine

in the processing and in cut precision.

• When cutting plastic material, please always use

clamps: the parts which should be cut must always

be xed between the clamps.

• Avoid accidental starting of the machine: the oper-

ating button may not be pressed when inserting the

plug in an outlet.

• Use the tool that is recommended in this manual. In

doing so, your saw provides optimal performance.

• Hands may never enter the processing zone when the

machine is in operation. Release the handle button

and switch off the machine prior to any operations.

• Prior to any adjustment, maintenance or service work

disconnect the mains power plug!

6. Technical data

AC motor 230 V~ 50Hz

performance 2000 Watt

operating mode S6 40%*

Idle speed 4800 min

-1

Hard-metal blade ø 254 x ø 30 x 2,8 mm

Number of teeth 24 / 48

Thickness riving knife 2,5 mm

minimum size work piece wxlxh 10x50x1 mm

table size 630 x 445 mm

Table width extension left/rights 620 x 250 mm

Table length extension rear 435 x 320 mm

Cutting height max. 90° 73 mm

Cutting height max. 45° 63 mm

height adjustment 0 - 73 mm

saw blade swivel 0 - 45°

suction port ø 34 mm

weight 28,5 kg

Laser class 2

Wavelength of laser 650 nm

Laser output < 1 mW

Laser module power supply

2 x 1,5 V

Micro (AAA)

* operating mode S6 40%: Continuous operation with in-

termittent loading (playing time 10 min).

Engine protection of to hot warming up:

It´s allowed to run the engine with nominal power maximum

40% of playing time. After this the machine must run 60% of

playing time steadily without load.

Noise values

The total noise values determined in accordance with

EN 61029.

sound pressure level L

96,2 dB(A)

uncertainty K

3 dB

sound power level L

109,2 dB(A)

uncertainty K

3 dB

Wear hearing protection.

The effects of noise can cause a loss of hearing. Total

vibration values (vector sum - three directions) deter-

mined in accordance with EN 61029.

7. Before starting the equipment

• The equipment must be set up where it can stand

securely, i.e. it should be bolted to a workbench, a

universal base frame or similar.

• All covers and safety devices have to be properly t-

ted before the equipment is switched on.

• It must be possible for the blade to run freely.

• When working with wood that has been processed

before, watch out for foreign bodies such as nails or

screws, etc.

• Before you press the ON/OFF switch check that the

saw blade is tted correctly. Moving parts must run

smoothly.

• Before you connect the equipment to the power sup-

ply make sure the data on the rating plate are dentical

to the mains data.

• Connect the machine to a properly installed protec-

tive contact socket, with at least 16A circuit breaker.

8. Attachment

Important. Pull out the power plug before carrying

out any maintenance, resetting or assembly work on

the circular saw!

Place all parts supplied on a at surface. Grouping

equal parts.

Note: If compounds with a bolt (round head / or hexa-

gon), hex nuts and washers are backed up, the washer

must be tted under the nut.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PTK 2000 A1 - IAN 104416 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,32 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside PTK 2000 A1 - IAN 104416 Manual

Product: