Manual Parkside PTK 2000 A1 - IAN 104416 (page 14 of 64) (English, German, Dutch, French)

595333

Zoom out

Zoom in

1/64

9GB

– Report faults on the electric tool, protective

devices or the tool attachment to the person

responsible for safety as soon as they are dis-

covered.

3 Safe work

– Use the push stick or handle with sliding wood,

to pass the workpiece securely out off the saw

blade.

– Make sure that the riving knife is always used,

and set up is correctly.

– Use the upper blade guard and set it to the cor-

rect position.

– Only use saw blades for which the maximum

permissible speed is not lower than the maxi-

mum spindle speed of table saws and which are

suitable for the material to be cut.

– Do not cut rebates or grooves without tting a

suitable guard, e.g. a tunnel-type guard, over the

saw table.

– Circular saws must not be used for slotting jobs

(cutting grooves which end in the workpiece).

– When transporting the electric tool, only use

the transport devices. Never use the protective

devices for handling or transport.

– Make sure that the upper part of the saw blade

is covered during transport, e.g. by the protective

device.

– Be sure to only use spacers and spindle rings

specied by the manufacturer as suitable for the

intended purpose.

– The oor around the machine must be level,

clean and free of loose particles, such as chips

and cutting residues.

– Always stand to the side of the saw blade when

working with the saw.

– Do not remove any cutting residues or other

parts of workpieces from the cutting zone while

the machine is running and the saw unit is not

at rest.

– Make sure that the machine is always secured

on a workbench or a table if at all possible.

– Support long workpieces (e.g. with a roller table)

to prevent them sagging at the end of a cut.

– m Attention! Never remove loose splinters, chips

or jammed pieces of wood while the saw blade is

running.

• Switch off the machine to troubleshoot or remo-

ve jammed pieces of wood. - Disconnect the

main power plug -

• Retting, including adjusting and measuring

works, and cleaning must be carried out only

when the motor is switched off. - Disconnect

the main power plug -

• Before switching on again, ensure that keys

and adjustment tools have been removed.

Warning! This electric tool generates an electromag-

netic eld during operation. This eld can impair active

or passive medical implants under certain conditions. In

order to prevent the risk of serious or deadly injuries, we

recommend that persons with medical implants consult

with their physician and the manufacturer of the medical

implant prior to operating the electric tool.

SAFETY INSTRUCTIONS FOR THE HANDLING OF

SAW BLADES

1 Only use insertion tools if you have mastered their

use.

2 Observe the maximum speed. The maximum

speed specied on the insertion tool may not be

exceeded. If specied, observe the speed range.

3 Observe the motor / saw blade direction of rota-

tion.

4 Do not use any insertion tools with cracks. Sort out

cracked insertion tools. Repairs are not permitted.

5 Clean grease, oil and water off of the clamping

surfaces.

6 Do not use any loose reducing rings or bushes for

the reducing of holes on saw blades.

7 Make sure that xed reducer rings for securing the

insertion tool have the same diameter and have at

least 1/3 of the cutting diameter.

8 Make sure that xed reducer rings are parallel to

each other.

9 Handle insertion tool with caution. They are ideally

stored in the originally package or special contain-

ers. Wear protective gloves in order to improve

grip and to further reduce the risk of injury.

10 Prior to the use of insertion tools, make sure that

all protective devices are properly fastened.

11 Prior to use, make sure that the insertion tool

meets the technical requirements of this electric

tool and is properly fastened.

12 Only use the supplied saw blade for sawing opera-

tions in wood, materials similar to wood, plastics

and non-ferrous metals (except for magnesium and

alloys containing magnesium).

Attention: Laser radiation

Do not stare into the beam

Class 2 laser

Protect yourself and you environment from acci-

dents using suitable precautionary measures!

• Do not look directly into the laser beam with unpro-

tected eyes.

• Never look into the path of the beam.

• Never point the laser beam towards reecting sur-

faces and persons or animals. Even a laser beam

with a low output can cause damage to the eyes.

• Caution - methods other than those specied here

can result in dangerous radiation exposure.

• Never open the laser module. Unexpected exposure

to the beam can occur.

• If the saw is not used for an extended period of time,

the batteries should be removed.

• The laser may not be replaced with a different type

of laser.

• Repairs of the laser may only be carried out by the

laser manufacturer or an authorised representative.

Safety instructions for handling batteries

1 Always make sure that the batteries are inserted

with the correct polarity (+ and –), as indicated on

the battery.

2 Do not short-circuit batteries.

3 Do not charge non-rechargeable batteries.

4 Do not overcharge batteries!

5 Do not mix old and new batteries or batteries of

different types or manufacturers! Replace an entire

set of batteries at the same time.

6 Immediately remove used batteries from the device

and dispose of them properly!

7 Do not allow batteries to heat up!

8 Do not weld or solder directly on batteries!

9 Do not dismantle batteries!

10 Do not allow batteries to deform!

11 Do not throw batteries into re!

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PTK 2000 A1 - IAN 104416 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,32 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside PTK 2000 A1 - IAN 104416 Manual

Product: