Manual Parkside PTK 2000 A1 - IAN 104416 (page 17 of 64) (English, German, Dutch, French)

595333

Zoom out

Zoom in

1/64

12 GB

Important. Note the running direction.

The cutting angle of the teeth must point in run-

ning direction, i.e. forwards (see the arrow on

the blade guard (2) )

9. Ret and set the table insert (6) and the saw blade

guard (2) (see 8.5 and 8.6)

10. Check to make sure that all safety devices are prop-

erly mounted and in good working condition before

you begin working with the saw again.

9. Using the saw

9.1 On/Off switch (Fig. 23)

- The saw can be switched on by pressing the green

pushbutton „I“.

- The red pushbutton „0“ has to be pressed to switch

off the saw.

9.2 Cutting depth (Fig. 23)

Turn the round handle (8) to set the blade (5) to the

required cutting depth.

- Turn anti-clockwise: larger cutting depth

- Turn clockwise: smaller cutting depth

After each new adjustment it is advisable to carry out a

trial cut in order to check the set dimensions.

9.3 Setting the angle (Fig. 23)

With the table saw you can make diagonal cuts to the

left oriented to the stop bar from 0 ° to 45 °.

m Check before each cut, that between the stop bar

(e), cross-stop (13) and the saw blade (5) a collision is

not possible.

- Undo the xing handle (9).

- Turn the handle (9.1) to set the desired angle on the

scale.

- Lock the xing handle (9) again in the required angle

position.

9.4 Parallel stop

9.4.1 Stop height (Fig. 24-25)

- The stop rail (e) for the parallel stop (7) has two dif-

ferent guide faces (high and low).

- For thick material you must use the stop rail (e) as

shown in Fig. 26, for thin material (with a workpiece

thickness of less than 25 mm) you must use the stop

rail as shown in Fig. 26.1.

9.4.2 Turning the stop rail (Fig. 24-25)

- First undo the wing nuts (f) to turn the stop rail (e).

- The stop rail (e) can now by pulled off the guide rail

(h) and can be pushed back over it with the appropri-

ate guide.

- Retighten the wing nuts (f).

9.4.3 Cutting width (Fig. 27-28)

- The parallel stop (7) has to be used when making

longitudinal cuts in wooden workpieces.

- The parallel stop should be mounted on the right-hand

side of the saw blade (5).

- Place the parallel stop on the guide rail for the parallel

stop (12) from above (Fig. 28).

- There are 2 scales (j/k) on the guide rail for the paral-

lel stop (12) which show the distance between the

stop rail (e) and the saw blade (5) (Fig. 27).

- Depending on this, choose the appropriate scale to

suit whether the stop rail (e) is turned for thick or thin

material:

High stop rail (thick material):

Scale j

Low stop rail (thin material):

Scale k

- Set the parallel stop (7) for the required dimension

using the inspection window (I) and secure it using the

eccentric lever for the parallel stop (31).

9.4.4 Adjusting the stop length (Fig. 29)

- The stop rail (e) can be moved in longitudinal direc-

tion in order to prevent the workpiece from becoming

jammed.

- Rule of thumb: The rear end of the stop comes up

against an imaginary line that begins roughly at the

center of the blade and runs at an angle of 45° to the

rear.

- Set the required cutting width.

- Slacken the wing nuts (f) and push the stop rail (e)

forward until it touches the imaginary 45° line.

- Tighten the wing nuts (f) again.

9.5 Adjusting the parallel stop (Fig. 30)

m Remove protective cap

- Set the saw blade (5) to maximum cutting depth (see

9.2).

- Set the parallel stop (7) so that the stop rail (e)

touches the saw blade (setting for thick material, also

see Point 9.4).

- If the parallel stop (7) is not in line with the saw blade

(5), undo the screws (m) on the parallel stop until the

parallel stop (7) can be adjusted in line with the saw

blade (5) (Figure 30).

- Re-tighten the screws (m).

9.6 Cross stop (Fig. 31)

• Slide the cross stop (13) into the groove (32) of the

table.

• Slacken the knurled screw (33).

• Turn the cross stop (13) until the required angle is set.

The notch (w) indicates the set angle.

• Retighten the knurled screw (33).

• When cutting you must use the stop rail (e) from the

parallel stop (7) to extend the length of the cross stop

(13) (Fig. 31-32)

• To extend the cross stop (13) with the stop rail (e), the

stop rail (e) must be removed of the parallel stop (7).

Now mount the stop rail as shown in Fig. 32, using the

wing nuts.

Important.

- Do not push the stop rail (e) too far toward the blade.

- The distance between the stop rail (e) and the blade

(5) should be approx. 2 cm (Fig. 31)

9.7 Adjusting the scale on the cross stop (Fig.

32)

- Place a 90° stop angle against the saw blade (5).

- Connect the cross stop (13) to the stop rail (e) of the

parallel stop (7) (see 9.6).

- Undo the knurled screw (33) of the cross top (13).

- Position the cross stop (13) so that the stop rail is in

a 90° angle to the saw blade (5). Now precisely align

the cross stop to the saw blade using the 90° stop

angle and retighten the knurled screw (33).

- Check if the cross stop is aligned at exactly 90°. If

this is not the case, continue as follows:

- Undo the two screws (o) holding the scale (p) to

the cross stop (13) until the scale can be set to

the correct position.

- Retighten the screws (o).

9.8 Using the laser (Fig. 34-35)

- The laser (34) enables you to make precision cuts

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PTK 2000 A1 - IAN 104416 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,32 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside PTK 2000 A1 - IAN 104416 Manual

Product: