773450

Parkside PSBS 240 C2 - IAN 321203 Manual

27
Zoom out
Zoom in
Previous page
1/124
Next page
27
IEGB
Insert the screws through the 4 bore
holes (13) on the base of the device.
The screws and nuts required for
assembly are not part of the scope
of delivery.
Operation
Caution! Risk of injury!
- Always disconnect the plug from
the mains socket before working.
- Use only grinding disks and acces-
sories recommended by the manu-
facturer. The use of other insertion
tools and other accessories may
cause risk of injury.
- Only use grinding tools which bear
information about the manufacturer,
type of binding, dimension and
permitted number of revolutions.
- Only use grinding discs where the
printed rotational speed is at least
as high as what has been specied
on the name plate of the device.
- Do not use broken, cracked or other-
wise damaged grinding disks.
- Never operate the device without
the visual protection disk.
- Always use protective goggles even
if you are protected against sparks.
- Always inspect the grinding disc
before starting the device:
Check the distance between the
spark protection and grinding disc
as well as workpiece support and
grinding disc (distance maximum
2 mm).
- The grinding disc must be replaced
once the spark protection and
workpiece support on the grinding
disc do not have distance of max.
2 mm.
- Switch on the equipment only when
it is safely installed on the work sur-
face.
Keep your hands away from
the grinding disc and grind-
ing belt when the device is in
operation. Injury hazard!
Switching on and off
Ensure that the mains voltage
matches the specications on the
rating plate.
Connect the equipment to the
mains.
1. To switch on, press the “I” On switch
and the device starts up (see 14a).
2. To switch off, press the “0” off switch
and the device switches off (see
14b).
After switching on the device, wait until the
device has reached its max. speed. Only
then must you start with the grinding.
The disk will continue to
run after the equipment is
switched off. There is a risk
of injury.
Test run:
Before starting work and after each
change of grinding disk, carry out a test
run of at least 60 seconds with no load.
Switch off the equipment immediately if the
disk runs lumpy, substantial vibrations oc-
cur, or abnormal noises are generated.
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PSBS 240 C2 - IAN 321203 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PSBS 240 C2 - IAN 321203 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 1.94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info