796092

Parkside PPSK 40 A2 - IAN 383214 Manual

10
Zoom out
Zoom in
Previous page
1/89
Next page
10 GB/IE/NI
or have been instructed in how to use the device safely and
understand the dangers that may arise when using it. Do not allow
children to play with the device. Cleaning and day-to-day mainte-
nance must not be performed by children without supervision.
Repairs and/or maintenance work must only be carried out by
qualified electricians.
Only use the cutting cable provided in the scope of delivery.
During operation, the device should not be positioned directly
against the wall, covered or jammed between other devices so
that sufficient air can always be absorbed through the ventilation
slats. Make sure that the device is correctly connected to the supply
voltage. Avoid any form of tensile stress of the power cable.
Disconnect the mains plug from the socket prior to setting up the
device in another location.
If the device is not in operation, always switch it off by pressing
the ON/OFF switch and lock the interlock switch. Place the burner
on an insulated surface and only carry out maintenance work after
allowing it to cool down for 15 minutes.
Hot metal and sparks are blown off from the cutting arc. The flying
sparks, hot metal as well as hot objects and hot device equipment
can cause fires or burns. Check the working environment and make
sure the workplace is suitable prior to using the device.
Remove all flammable material within 10 m of the plasma cutter. If this
is not possible, cover the objects meticulously using suitable covers.
Do not make cuts in places where flying sparks could come into
contact with flammable material.
Protect yourself and others from flying sparks and hot metal.
Please be careful because sparks and hot materials can easily
fall through small gaps and openings while cutting and land on
adjacent areas.
Please be aware that cutting on a ceiling, floor or a partition can
cause a fire on the opposite side that is not visible.
Connect the power cable using the shortest route with a socket
situated close to the workplace to prevent the power cable from
being spread across the whole room and located on a surface
which could cause an electric shock, sparks or fire outbreak.
Do not use the plasma cutter to defrost frozen tubes.
RISK OF ELECTRIC SHOCK:
ELECTRIC SHOCK FROM THE CUTTING
ELECTRODE CAN BE FATAL.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PPSK 40 A2 - IAN 383214 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PPSK 40 A2 - IAN 383214 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1.86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info