763020

Parkside PPS 40 B2 - IAN 327358 Manual

21
Zoom out
Zoom in
Previous page
1/49
Next page
21GB/IE/NI
Troubleshooting / Maintenance and care
Arc stops during
cutting? Cutting speed too low.
Plasma burner 8 is held too
high and too far away from
the material.
Plasma burner component
parts are worn 8b, 8c , 8d, 8e .
Workpiece no longer
connected to the grounding
cable.
Increase the cutting speed until
the problem no longer exists.
Lower the plasma burner 8 to
the recommended height.
Check and replace worn
parts.
Check the connections.
Insufficient
penetration? Cutting speed too fast.
Burner sleeve 8c is not straight
Metal is too thick.
Plasma burner component
parts are worn 8b, 8c , 8d, 8e .
Slow down the working speed
Adjust the inclination.
Several cycles necessary.
Check and replace worn
parts.
Consumables
wear quickly? Performance was over-
stretched.
Arc control time exceeded.
Incorrect plasma burner
assembly.
Insufficient air supply, pressure
too low.
Faulty air compressor.
Material too thick, increase
the angle to avoid material
from being blown back into
the tip.
Do not control the arc for
more than 5 seconds. You can
also start with contact
between the burner sleeve 8c
and metal or with a 3.2 mm
distance to the metal.
Check the air filter, increase
the air pressure.
Check the performance of the
air compressor and make sure
the inlet pressure is at least
100 PSI (6.8 bar).
• Maintenance and care
• Maintaining the burner
The parts displayed in Figure F are the
electrode 8d, diffuser 8e and the burner
sleeve 8c . They can be replaced once
the nozzle clamping sleeve 8b has been
unscrewed.
The electrode 8d must be replaced if
there is a crater of approximately
1.5 mm depth in the centre.
ATTENTION!
fTo unscrew the electrode, do not apply
irregular pressure, gradually increase
pressure until the thread is released.
The new electrode must be screwed into
its bracket and blocked but not tightened
up to the stop.
327358_Plasmaschneider_PPS_40_B2_content_LB6_IE_NI.indb 21 06.09.2019 12:41:03
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PPS 40 B2 - IAN 327358 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PPS 40 B2 - IAN 327358 in the language / languages: English, German as an attachment in your email.

The manual is 2,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info