796059

Parkside PPFSA 40-Li A1 - IAN 376667 Manual

47
Zoom out
Zoom in
Previous page
1/236
Next page
47
GB IE
• Always hold the device tightly and se-
curely with both hands!
• Only cut grass and weeds! Watch out
for roots or tree stumps, there is a risk
of tripping.
• Work carefully and do not endanger
anyone while you are strimming.
• You should only work in good lighting
conditions with sufcient visibility!
• Keep an eye on the cutting head!
• Never strim above shoulder height!
• Never replace the plastic cord with
steel wire - risk of injury and destruc-
tion!
• Never work on a ladder!
• Only work on rm and stable surfaces!
• Avoid an abnormal work posture.
Ensure that your footing is secure and
keep your balance at all times.
• Change your working position at regu-
lar intervals in order to prevent becom-
ing tired on one side of your body.
• If the cutting head becomes jammed,
turn the device off immediately, remove
the spark plug connector and then re-
move the cause of the blockage.
Adjusting the shoulder strap
eyelet/balancing out the
device
Select the correct position for the shoulder
strap eyelet for the spool and blade.
Without touching it by hand, the device
attached to the shoulder strap should be as
follows
The spool should rest lightly on the
ground.
The blade should be balanced
around 20 cm above the ground.
1. Loosen the screw on the shoulder strap
eyelet (12). Slightly tighten the screw
again.
2. Depending on the cutting tool, balance
the device according to the criteria
mentioned above by moving the eyelet
(12) along the upper shaft tube (3).
3. Tighten the screw when the device is in
the desired position.
Working using the thread
spool
• In small grass areas hold the device at
an angle of about 30° and swing the
cutting head evenly to the right and left
with a semi-circular movement.
• The best results are obtained with a
maximum grass length of 15 cm. If the
grass is taller, it is recommended to
mow several times.
• To cut around trees, fence posts or
other obstacles, slowly move the device
around the obstacle and cut with the
thread ends.
• Avoid any contact with xed obstacles
(rocks, walls, picket fences, etc.). The
thread would wear out quickly. Use the
edge of the protective cover to keep the
device at the correct distance.
Attention! Do not lay the cut-
ting head on the ground dur-
ing operation!
Extending the line
Your device is equipped with a dual-line
auto-tap feature, i.e. the two strings are
extended when you tap the cutting head
on the ground.
1. Hold the device in operation over a
grassy area and lightly tap the cutting
… 47 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PPFSA 40-Li A1 - IAN 376667 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PPFSA 40-Li A1 - IAN 376667 in the language / languages: English, German, Dutch, Danish, French, Polish, Spanish as an attachment in your email.

The manual is 3.76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info