786099

Parkside PKO 24 A1 - IAN 339151 Manual

19
Zoom out
Zoom in
Previous page
1/80
Next page
14 GB/IE
6. Safety information
m Attention!
The following basic safety measures must be observed when
using electric tools for protection against electric shock, and the
risk of injury and fire. Read all these notices before using the
electric tool and keep the safety instructions for later reference.
Safe work
1. Keep the work area orderly
- Disorder in the work area can lead to accidents.
2. Take environmental influences into account
- Do not expose electric tools to rain.
- Do not use electric tools in a damp or wet environment.
There is a risk of electric shock!
- Make sure that the work area is well-illuminated.
- Do not use electric tools where there is a risk of fire or
explosion.
3. Protect yourself from electric shock
- Avoid physical contact with earthed parts (e. g. pipes,
radiators, electric ranges, cooling units).
4. Keep children away
- Do not allow other persons to touch the equipment or
cable, keep them away from your work area.
5. Securely store unused electric tools
- Unused electric tools should be stored in a dry, elevated
or closed location out of the reach of children.
6. Do not overload your electric tool
- They work better and more safely in the specified output
range.
7. Wear suitable clothing
- Do not wear wide clothing or jewellery, which can be-
come entangled in moving parts.
- Rubber gloves and non-slip shoes are recommended
when working outdoors.
- Tie long hair back in a hair net.
8. Do not use the cable for purposes for which it is not in-
tended
- Do not use the cable to pull the plug out of the outlet.
Protect the cable from heat, oil and sharp edges.
9. Take care of your tools
- Keep your compressor clean in order to work well and
safely.
- Follow the maintenance instructions.
- Check the connection cable of the electric tool regularly
and have it replaced by a recognised specialist when
damaged.
- Check extension cables regularly and replace them
when damaged.
10. Pull the plug out of the outlet
- During non-use of the electric tool or prior to mainte-
nance and when replacing tools such as saw blades,
bits, milling heads.
11. Avoid inadvertent starting
- Make sure that the switch is switched off when plugging
the plug into an outlet.
12. Use extension cables for outdoors
- Only use approved and appropriately identified exten-
sion cables for use outdoors.
- Only use cable reels in the unrolled state.
13. Remain attentive
- Pay attention to what you are doing. Remain sensible
when working. Do not use the electric tool when you
are distracted.
14. Check the electric tool for potential damage
- Protective devices and other parts must be carefully in-
spected to ensure that they are fault-free and function as
intended prior to continued use of the electric tool.
- Check whether the moving parts function faultlessly and
do not jam or whether parts are damaged. All parts
must be correctly mounted and all conditions must be
fulfilled to ensure fault-free operation of the electric tool.
- Damaged protective devices and parts must be properly
repaired or replaced by a recognised workshop, insofar
as nothing different is specified in the operating manual.
- Damaged switches must be replaced at a customer ser-
vice workshop.
- Do not use any faulty or damaged connection cables.
- Do not use any electric tool on which the switch cannot
be switched on and off.
15. Have your electric tool repaired by a qualified electrician
- This electric tool conforms to the applicable safety regu-
lations. Repairs may only be performed by an electri-
cian using original spare parts. Otherwise accidents can
occur.
16. Important!
- For your own safety you must only use the accessories
and additional units listed in the operating instructions or
recommended or specified by the manufacturer. The use
of mounted tools or accessories other than those recom-
mended in the operating instructions or catalogue may
place your personal safety at risk.
17. Noise
- Wear ear muffs when you use the compressor.
18. Replacing the power cable
- To prevent hazards, leave the replacement of damaged
power cables strictly to the manufacturer or a qualified
electrician. There is a risk of electric shock!
19. Inflating tires
- Directly after inflating tires, check the pressure with a suit-
able pressure gauge, for example at your filling station.
20. Roadworthy compressors for building site operations
- Make sure that all lines and fittings are suitable for the
maximum permissible operating pressure of the com-
pressor.
21. Place of installation
- Set up the compressor on an even surface.
22. Supply hoses at pressures above 7 bar should be equipped
with a safety cable (e. g. a wire rope).
23. Avoid over-stressing the piping system by using flexible
hose connections to prevent kinking.
24. Ensure that oil cooling devices are kept clean.
25. Risk of burns from hot oil
-Wear suitable protective gloves.
-Never work with the compressor near naked flames.
-Be careful not to spill oil.
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PKO 24 A1 - IAN 339151 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PKO 24 A1 - IAN 339151 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 6.05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info