706381

Parkside PHKS 1300 A1 - IAN 67034 Manual

14
Zoom out
Zoom in
Previous page
1/33
Next page
12 GB/IE
J
Looking at the laser output
aperture
12 a
with optical instruments (e.g.
magnifying glass, magnifying lens, etc.) could
result in eye damage.
J Never direct the laser beam on to reflective
surfaces or at people or animals. Even a brief
look into a laser beam can damage your eyes.
Changing batteries:
J Open the battery compartment cover
10
using
a suitable cross-head screwdriver (see Fig. G).
J Remove the used batteries.
J Observing the correct polarity, insert two new
1.5 V alkaline batteries type LR44 (e.g. GPA 76)
and screw the battery compartment cover
10
tightly in place again.
CAUTION! The use of operating or adjustment
devices or other methods of working other than
those indicated in this document may lead to
exposure to hazardous radiation.
Working safely:
J If a dangerous situation arises, pull the mains
plug immediately out of the mains socket.
J Never use the device for a purpose for which it
was not intended.
J Always keep the device clean, dry and free of
oil or grease.
J If the saw is used whilst fixed in place on a saw ta-
ble then the saw table must have a restart cut-out.
J Make sure the device is switched on before
placing it against the workpiece.
J Always work away from your body.
J Do not saw materials containing asbestos.
J The course of the cut must have no obstructions
above or below it.
J The saw blade must not project more than
3 mm out of the workpiece.
J When you are sawing, always make sure that you
do not cut through any nails, screws or the like.
J Do not work with the device in the overhead
position.
J Protect the saw blade from sharp blows or im-
pacts and prevent it from becoming tilted.
J When you switch off the saw, allow the blade
to slow down naturally - do not assist this pro-
cess in any way.
J Cracked or distorted blades are not to be used.
HSS (High Speed Steel) saw blades are not to
be used.
J Before carrying out any work on the saw, e.g.
setting the base plate etc. always pull the
mains plug out of the mains socket.
J Never remove sawdust or splinters whilst the
saw is running.
J Have a suitable, tested vacuum removal device
attached to the saw when working with woods
or materials that create dusts that may be haz-
ardous to health.
J Always use the safety devices integrated into
the circular saw, e.g. the safety lock-out
2
and automatic blade guard
7
.
J Ensure that all moving parts of the saw blade
protection system function properly and all the
assemblies and components involved in cover-
ing the saw blade are in perfect working order.
J Do not lock on the ON / OFF switch
3
in
hand-guided operation.
Q
Preparing for use
The PHKS 1300 A1 circular saw has Intelligent
Power Control.
This automatic power
delivery system ensures
that for a particular
speed range the power output remains constant when
working on harder and more resistant materials.
Q
Switching on and off
Switching on:
j Press the safety lock-out
2
to the left or right
and keep it pressed.
j Press the ON / OFF switch
3
. Once the saw
is running you can release the safety lock-out
2
again.
The circular saw is fitted with an
electronic soft start system. The
motor starts with a delay.
General safety advice for electrical power tools / Preparing for use
67034_par_Handkreissaege_PHKS1300A1_Content_LB6.indd 12 30.06.11 16:59
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PHKS 1300 A1 - IAN 67034 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PHKS 1300 A1 - IAN 67034 in the language / languages: English as an attachment in your email.

The manual is 6,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PHKS 1300 A1 - IAN 67034

Parkside PHKS 1300 A1 - IAN 67034 User Manual - German, Dutch, French, Italian - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info