Manual Parkside PHKS 1300 A1 - IAN 67034 (page 13 of 33) (English)

706381

Zoom out

Zoom in

1/33

11 GB/IE

from rotating and the force of the motor throws

the device back in the direction of the operator.

c) If the sawblade distorts or becomes misaligned

in the saw cut, the teeth at the rear edge of the

sawblade may hook themselves into the work-

piece surface causing the sawblade to move

out of the saw gap and the circular saw to jump

backwards in the direction of the operator.

Special safety advice for circular saws

and automatic blade guards

a) Before you use the saw, always check

that the automatic blade guard

clos-

es properly. Do not use the saw if the

bottom compartment of the blade

guard

does not move freely or close immedi-

ately. Never jam or tie the automatic

blade guard in the open position. The

bottom part of automatic blade guard may be-

come bent if the saw falls on to the ﬂoor. Open

the blade guard with the release lever and make

sure that it moves freely and does not touch the

saw blade or other parts at all cutting angles

and depths.

b) Check that the spring on the automatic

blade guard functions properly. If the

automatic blade guard or spring does

not function properly, have the device

serviced before you use it. Damaged

parts,

sticky deposits or accumulations of splinters can

delay the operation of the bottom blade guard.

c) Open the automatic blade guard by

hand only for certain cuts such as

plunge

or angle cuts. Open the automatic

blade

guard with the release lever

7 a

and

let it go again as soon as the saw blade

penetrates the workpiece. The automatic

blade guard must be allowed to operate auto-

matically for all saw cuts.

d) Do not put the saw down on a work

bench or the floor without the auto-

matic blade guard covering the saw

blade. If unprotected, a rotating saw blade

moves the saw against the cutting direction and

saws whatever is in its way. Always be aware

that the saw blade takes some time to stop.

Special safety advice for circular saws

and riving knives

a) Use the riving knife matched to the in-

stalled saw blade. The riving knife must be

thicker than the body of the blade but thinner

than the width of the teeth.

b) Adjust the riving knife as described in

the operating instructions. If its thickness,

position or alignment is incorrect, this can lead

to the riving knife not eﬀectively preventing

kickback.

c) Always use the riving knife, except

for plunge cuts. After completing plunge

cutting, put the riving knife back in place. The

riving knife interferes with plunge cuts and can

result in kickback.

d) For the riving knife to work properly,

it must be within the saw gap. The riv-

ing knife is ineﬀective in preventing kickback

for short cuts.

e) Do not operate the saw if the riving

knife is bent out-of-true. Even a slight defect

can cause the blade guard to close too slowly.

WARNING! Protecting yourself

from laser radiation:

LASER RADIATION

DO NOT STARE INTO BEAM

CLASS 2 LASER PRODUCT

P max.: < 1 mW ·

: 650 nm

EN 60825-1: 2007

J Do not look directly into the laser beam or into

the opening from which it is emitted.

General safety advice for electrical power tools

67034_par_Handkreissaege_PHKS1300A1_Content_LB6.indd 11 30.06.11 16:59

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PHKS 1300 A1 - IAN 67034 in the language / languages: English as an attachment in your email.

The manual is 6,11 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PHKS 1300 A1 - IAN 67034

Parkside PHKS 1300 A1 - IAN 67034 User Manual - German, Dutch, French, Italian - 60 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside PHKS 1300 A1 - IAN 67034 Manual

Product: