Manual Parkside PDS 120 B2 - IAN 322849 (page 11 of 60) (English, German, Dutch, French)

779497

Zoom out

Zoom in

1/60

6GB/IE/NI

• Workpieces that are smaller than the saw blade guard can

cause injuries to the hands or ﬁngers. Use suitable aids!

• Avoid cramped hand positions when guiding in the work-

piece and avoid positions in which slipping could lead to

your hand making direct contact with the saw blade.

• Always ﬁt the saw blade with the teeth facing in the direction

of the sawing table.

• Always set the correct blade tension to prevent the saw

blades from jerking.

• Be especially careful when cutting material with irregular cut

proﬁles.

• Exercise particular caution when cutting round objects such as

rods and pipes. These can roll down into the saw blade and

cause the teeth to catch. Use a wedge to brace such work-

pieces.

• The teeth can become caught in the kerf when the workpiece

is pulled back, especially if sawings have ﬁlled in (blocked)

the kerf. In this case, you should switch the saw oﬀ, pull the

power plug, clear the kerf with a wedge, and remove the

workpiece.

• Never leave the work area without having already switched

the saw oﬀ. Wait until the saw stops moving completely.

• Do not position, join, or construct any parts on the work table

while the saw is running.

• Only switch the saw on after you have removed any remain-

ing material and tools from the work table. Leave only the

workpiece to be machined and any aids (e.g. wedges) on

the work table.

• Always wear safety goggles!

• Keep your ﬁngers at a safe distance from the saw blade.

• Carefully guide the workpiece and keep it steady at all times.

• Never leave the work area without having already switched

the saw oﬀ.

• Do not let your familiarity with the saw allow you to be care-

less. Carelessness can lead to severe injuries within a frac-

tion of a second.

• Working position is always laterally of the saw blade.

Do not lose this safety information.

7. Technical data

Mains voltage ...........................................220-240 V~/50 Hz

Power input ...............................................80 Watt (S1*)

.................................................................120 Watt (S6 30%**)

Stroke rate .................................................500-1700 min-1

Protection type ..........................................IP 20

Stroke ........................................................12 mm

Base area..................................................630 x 295 mm

Tilting range of table ................................0° bis 45° nach links

Table size ..................................................415 x 255 mm

Length of saw blade approx. ..................134 mm

Reach ........................................................406 mm

Max. cutting height at 90° .....................50 mm

Max. cutting height at 45° .....................22 mm

Minimum size work piece w x h .............. 100 x 22 mm

Maximum size work piece w x h ............400 x 50 mm

Weight ......................................................13.2 kg

*Operating mode S1:

Continuous operation at constant load

**Operating mode S6 30%:

Continuous operation with idling (cycle time 10 minutes). To

ensure that the motor does not become excessively hot, it may

only be operated for 30% of the cycle at the speciﬁed rating

and must then be allowed to idle for 70% of the cycle.

Noise emission values

Sound

Sound values were measured in accordance with EN 61029.

Wear ear-muﬀs.

The impact of noise can cause damage to hearing.

Sound pressure level LpA ........................................... 66,9 dB(A)

Uncertainty KpA ............................................................... 3 dB(A)

Sound power level LWA ............................................. 79,9 dB(A)

Uncertainty KWA .............................................................. 3 dB(A)

The quoted values are emission values and not necessarily reli-

able workplace values. Although there is a correlation between

emission and imission levels it is impossible to draw any certain

conclusions as to the need for additional precautions.

Factors with a potential inﬂuence on the actual immission level

at the workplace include the duration of impact, the type of

room, and other sources of noise etc., e. g. the number of ma-

chines and other neighbouring operations.

Reliable workplace values may also vary from country to coun-

try. With this information the user should at least be able to

make a better assessment of the dangers and risks involved.

Limit the noise level to a minimum!

• Use only equipment that is in perfect condition.

• Maintain and clean the equipment regularly.

• Adopt your way of working to the equipment.

• Do not overload the equipment.

• Have the equipment checked if necessary.

• Switch oﬀ the equipment when not in use.

Suitable saw blades

All industry-standard saw blades with a minimum length of

127mm with and without a pin may be used.

8. Before starting the machine

8.1 Unpacking

• Open the packaging and remove the device carefully.

• Remove the packaging material as well as the packaging

and transport bracing (if available).

• Check that the delivery is complete.

• Check the device and accessory parts for transport damage.

• If possible, store the packaging until the warranty period has

expired.

ATTENTION

The device and packaging materials are not toys!

Children must not be allowed to play with plastic

bags, ﬁlm and small parts! There is a risk of swal-

lowing and suﬀocation!

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PDS 120 B2 - IAN 322849 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2.52 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside PDS 120 B2 - IAN 322849 Manual

Product: