779497

Parkside PDS 120 B2 - IAN 322849 Manual

12
Zoom out
Zoom in
Previous page
1/60
Next page
7GB/IE/NI
8.2 General notes
• All covers and safety devices have to be properly fitted be-
fore the equipment is switched on.
• It must be possible for the blade to run freely.
• When working with wood that has been processed before,
watch out for foreign bodies such as nails or screws, etc.
• Before you actuate the On/Off switch, make sure that the
saw blade is correctly fitted and that the equipment’s moving
parts run smoothly.
• Check that the voltage on the rating plate is the same as
your supply voltage before you connect the equipment to
the power supply.
• Only ever connect the equipment to a properly installed
shock-proof socket which is protected by a 10A fuse as a
minimum.
8.3 Installing the fretsaw on a workbench
Required for installing:
Included in the scope of delivery:
• M8 hex screw (4x)
• M8 hex nut (4x)
• Washer Ø 9 mm (8x)
Not included in the scope of delivery:
• Flat gasket Ø 7 mm (4x)
• Rubber base: 410 x 255 x 13 mm
The length of the screws to be used varies, depending on the
thickness of the table top.
WARNING
Danger of injury! Disconnect the mains plug on the scroll saw
before all assembly work.
1. The length of the screws to be used varies, depending on
the thickness of the table top.
2. Mark the drill holes. Use the fretsaw as a template for
this purpose.
3. Drill 4 holes with a diameter of 8mm into the work table
and the rubber base.
4. Screw the scroll saw onto the workbench with the hex-
agonal bolt (G) through the assembly points (fig. 3 pos.
19) in the following sequence (fig. 5):
A Fretsaw
B Rubber base
C Work table
D Flat gasket
E Washer
F Hex nut
5. Tighten the hexagonal nut (F) first.
9. Assembly
WARNING
Danger of injury! Disconnect the mains plug on the scroll saw
before all assembly work.
9.1 Installing the depressor (fig. 6, 7)
NOTE:
Before assembling the depressor (24), the saw blade pre-in-
stalled at the factory (22) must be removed (see 9.3).
1. Remove the saw blade (22) as described in 9.3.
2. Remove the depressor (24) from the saw blade guard
(5) by loosening the screw (25) completely (see fig. 6).
3. Insert the holder (4) into the opening (see fig. 7).
4. Fasten the holder (4) with the knurled screw (3).
5. Install the depressor (24). Insert the screw (25) into the
holder (4) and fasten it.
6. Insert the saw blade (22) again as described in 9.3.
7. Ensure that the depressor (24) does not contact the saw
blade (22).
The depressor (24) must always be adjusted according to
the workpiece height. However, the workpiece should not be
clamped, but should rather be able to move freely.
The depressor (24) is used to lock the workpiece so that it
cannot swing upwards, which would destroy the saw blade
(22).
9.2 Installing the blow-off device (fig. 8)
1. Ensure that the saw blade guard (5) folded down.
2. Screw the blow-off device (1) clockwise onto the holder
(2) as described in fig. 8.
9.3 Changing the saw blade (fig. 1, 8-11)
IMPORTANT
To avoid injuries attributed to inadvertent startup:
Before removing or replacing the saw blade, al-
ways press “0“ and remove the mains plug from
the socket.
9.3.1 Removing the saw blade without pins (op-
tional)
1. To remove the saw blade (22) , lift the table insert (26)
upwards.
2. First, release the tension by flipping the tension lever (11)
upwards. Continue reducing the tension by turning clock-
wise as required.
3. Press the support (12) down lightly (see fig. 9).
4. Then loosen the upper saw blade clamping lever (28),
followed by the lower saw blade clamping lever (29) us-
ing the Allen key (23).
9.3.2 Inserting the saw blade without pins
(optional)
The teeth of the saw blade must always point downwards.
1. First, secure the saw blade (22) in the lower saw blade
mounting (30). To secure the saw blade (22), tighten the
lower saw blade clamping screw (29) using the Allen
key (23).
2. Press the support (12) down lightly. Fasten the other end
of the saw blade (22) in the top saw blade holder (27)
(see fig. 9).
3. Fix the saw blade (22) with the upper blade clamping
screw (28) (see fig. 10).
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PDS 120 B2 - IAN 322849 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PDS 120 B2 - IAN 322849 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2.52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info