679415
10
Zoom out
Zoom in
Previous page
1/64
Next page
PDEXS 125 A1
GB
IE
NI
 7
Before use
Selecting the grinding disc
Metal Removal and Surface:
The rate of metal removal and the surface quality
are determined by the grain size of the grinding
disc.
Lease note that corresponding grinding discs
with different grain sizes should be used for
processing different materials.
Changing sanding sheets
The air sander is fitted with a hook and loop faste-
ning, which allows for quick and easy replacement
of sanding discs.
Lift the grinding disc at the side and pull it off
from the backing pad in order to remove it.
HINWEIS
Before securing a new sanding sheet, remove
all dust and dirt from the sander plate .
Ensure that the openings in the sanding sheet
concur with the boreholes of the sanding plate .
Dust / swarf removal by suction
WARNING!
Please note the “Safety instructions” section.
Using the internal vacuum extraction with
dust collection device (see Fig. B):
Push the exhaust air hose fully on to the
connection for dust extraction .
You have to evert the opening of the dust bag
first, so that the straps are outside. Put the
opening of the dust bag over the free end of
the exhaust air hose and fasten the dust bag
firmly in position. In this way, the dust bag
can be tied tightly to the exhaust air hose .
NOTE
Empty the dust bag in good time and re-
gularly to ensure optimum dust extraction. To
do this open the zip fastener on the underside
of the dust bag .
Topping up the oil
In order for the air sander to have a long service
life, there must always be enough pneumatic oil in
the device.
NOTE
Use safe lubricants.
When determining which lubricants to use,
you must consider the environmental, occupa-
tional, and health aspects involved.
You may ensure this in any of the following
ways:
Connect a service unit with an oiler to the
compressor.
Install a line oiler in the compressed air line or
at the compressed air device.
Put approx. 3–5 drops of pneumatic oil by
hand into the plug nipple every 15 minutes
of operation.
Preparing for use
Connecting the compressed air source
NOTE
The air sander must be operated using
cleaned and condensate-free compressed
air only and its maximum allowable working
pressure of 6.3 bar at the device must not be
exceeded.
The compressed air source must be fitted
with a (filter) pressure reducer so that the air
pressure can be regulated.
Connect the plug nipple by a quick-release
coupler to the compressed air supply.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PDEXS 125 A1 - AN 304779 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PDEXS 125 A1 - AN 304779 in the language / languages: English, German, Dutch, Danish, French as an attachment in your email.

The manual is 0,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info