679415
11
Zoom out
Zoom in
Previous page
1/64
Next page
PDEXS 125 A1
8 
GB
IE
NI
Switching on and off
NOTE
Always switch on the air sander before
bringing it into contact with the workpiece
material.
Switching on the air sander:
Press the operator’s lever fully down
Set the speed using the speed control .
Switching off the air sander:
Release the operator’s lever .
After you finish work, disconnect the device
from the compressed air source.
NOTE
First disconnect the hose from the compressed
air source (compressor) and only then discon-
nect the compressed air supply hose from the
device. This will ensure that the compressed
air supply hose does not wave around in an
uncontrolled manner.
Advice on use
Wait until the device has come to a standstill
before you put it down.
Sanding surfaces
Switch the air sander on and bring the whole
of its sanding area into contact with the surface
to be abraded. Move it using even pressure to
and fro over the workpiece.
NOTE
The sanding output and appearance are
largely dependent on the choice of sanding
sheet and the pressure applied. A sanding
sheet must be free of defects to produce a
good sanding output.
Ensure that you use an even pressure. Excessive
pressure does not produce a higher sanding
output, it just increases the wear on the sanding
sheet.
A sanding sheet previously used on metal must
not be used on other materials.
Replacing the backing plate
WARNING! RISK OF INJURY!
Always disconnect the device from the com-
pressed air source before you replace the
backing plate
.
Push the open-ended spanner between the
backing plate and collar .
Release the backing plate by turning the pla-
te anticlockwise and holding the open-ended
spanner still against this movement.
Screw on a new backing plate clockwise
until tight while holding the open-ended spanner
still against this movement.
Maintenance and cleaning
WARNING! RISK OF INJURY!
Disconnect the appliance from the
compressed air supply.
CAUTION!
Before maintenance, clean off any hazardous
substances that may (due to working pro-
cesses) have accumulated on the appliance.
Avoid all skin contact with these substances.
If the skin comes into contact with hazardous
dusts, this can lead to severe dermatitis. If
dust is produced or swirled up during mainte-
nance, it can be inhaled.
NOTE
To ensure correct functioning and long-term
durability of the sander, pay attention to the
following points:
Sufficient and continuously intact oil lubrication
is highly important for optimum functioning.
Check the speed and vibration levels after each
use.
Check the idle speed regularly and after any
maintenance is performed:
use a rev counter and perform the measurement
without any clamped tools. The idle speed may
not be exceeded under any circumstances at a
residual pressure of 6.3 bar.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PDEXS 125 A1 - AN 304779 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PDEXS 125 A1 - AN 304779 in the language / languages: English, German, Dutch, Danish, French as an attachment in your email.

The manual is 0,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info