745084

Parkside IAN 89068 PABK 60 A1 Manual

38
Zoom out
Zoom in
Previous page
1/44
Next page
38 GB
General safety instructions … / Before initial use / Preparations for use
General safety instructions for compressed air tools
Maintain the device carefully. Check that mov-
ing device parts are working properly and move
freely. Check for any parts that are broken or
damaged enough to detrimentally affect the
functioning of the device. Have damaged parts
repaired before you use the device. Many ac-
cidents have their origins in poorly maintained
devices.
Switch off the device off when it is not in use.
Always wear personal protective
device and safety glasses. Wearing
personal protective devices such as
dust mask, non-slip safety shoes, safety helmet
or ear protectors, depending on the type of
compressed air tool and its application, reduces
the risk of injuries.
Check the connections and supply lines. All
maintenance units, couplings and hoses must be
equipped to meet the pressure and air amounts
specified in the device specific values. Pressure
that is too low influences the functioning of the
device; pressure that is too high can cause
damage to property and personal injury.
Protect hoses from kinks, constrictions, solvents
and sharp edges. Keep hoses away from heat,
oil and rotating parts.
Make sure that the hose clamps are always
tightly fastened. If the hose clamps are not
tightly fastened or are damaged, the air could
escape uncontrollably.
Replace damaged hoses immediately. A dam-
aged supply line may result in the air hose
whipping about and may result in injuries.
If the power cable of the device is damaged, it
has to be replaced by the manufacturer or its
service department or a similarly qualified per-
son in order to avoid hazards.
Do not use the device when tired or under the
influence of drugs, alcohol or medications. One
moment of carelessness when using the device
may result in serious injuries.
Do not directly inhale the exhaust air. Keep eyes
away from exhaust air. Exhaust air from the
compressed air device may contain water, oil,
metal particles or contamination from inside the
compressor. This may result in injury to health.
BE CAREFUL WHEN
SETTING DOWN THE DEVICE! Always put
down the device so it does not come into contact
with the trigger. This could potentially result in
accidental activation of the device, which again
could result in hazards.
Only use suitable accessories. These may be
purchased from the manufacturer. Using non-
OEM accessories may result in hazards.
Only use filtered and regulated compressed
air. Dust, caustic vapours and / or moisture may
damage the motor of a compressed air tool.
The hose must be designed for pres-
sures of at least 8.6bar or 125PSI,
but at least 150 % of the maximum
pressure generated in the system.
The tool and supply line must be
equipped with a hose coupling to
completely remove pressure when
disconnecting the coupling hose.
Do not modify this device in any way without
the manufacturer‘s approval.
Only use the compressed air device with the
specified pressure (max. 0.32 MPa / approx.
3 bar).
Disconnect the compressed air device from the
air supply after each use and when not in use.
Do not use the compressed air device if it leaks
or is in need of repair.
Never connect the compressed air device to an
air hose with pressure exceeding 7bar.
Keep your working area clean and well lit. Un-
tidy or poorly lit working areas can lead to ac-
cidents. Working under proper conditions will
allow you better control of the device, particu-
larly under unforeseen circumstances.
Only have the device repaired
by qualified specialist personnel using OEM
spare parts. This will ensure that your device
remains safe to use.
Keep children and other individuals away from
the device during use. Distractions can cause
you to lose control of the device.
Wear suitable clothing. Do not wear loose cloth-
ing or jewellery. Keep your hair, clothing and
gloves clear of moving parts. Loose clothing,
jewellery or long hair can become trapped in
moving parts.
89068_par_Airbrush_Set_Content_LB2.indd 38 04.06.13 09:56
… 38 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 89068 PABK 60 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 89068 PABK 60 A1 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info