Manual Parkside IAN 89068 PABK 60 A1 (page 40 of 44) (English, German, Dutch, French)

745084

Zoom out

Zoom in

1/44

40 GB

… / Cleaning and care / Information about warranty and service processing

Preparations for use

Clean dusty surfaces so that the suction cups can grip

well. Otherwise a slight shift in position is possible.

Connecting the airbrush set

Be absolutely certain to disconnect the mains

plug before connecting the airbrush set to the

compressor and release the pressure in the lines

by actuating the vent of the air blow gun

Use the respective screw connection to connect

the spray stylus

with the coiled hose

and

the coiled hose to the airbrush connection

Use the included open-end wrench.

(see Ill. A).

Fasten the paint mixing beaker with connection

lid

to the spray stylus

(see Ill. B).

Insert the mains plug into the mains socket.

Note: For optimal results, professionals connect

an intermediate pressure reducer (not included

with delivery). The pressure reducer can be used

to adjust the compressed air at the spray gun

and optimise it to your needs.

Mixing paints for use

The paints included are water-soluble. In order to

properly apply the paints, add water and stir. As

delivered, the paints are too viscous.

First ﬁll the beaker with your selected paint

colour with water.

Now screw the cover back on the beaker and

shake it.

Now use the pipette

to remove two drops

of the slightly diluted paint paste and add them

to a paint mixing beaker completely ﬁlled with

water (

Shake the beaker. Now your paint has reached

the correct consistency.

Attach the paint mixing glass (

) accord-

ing to Ill. B.

Note: If desired, you can adjust the amount of

water added to inﬂuence the colour intensity

yourself as with a watercolour box. The more

water you add, the „thinner“ the colour.

You can also mix individualised colour tones

from the available colour pastes. Please take

note, there must be no paint clumps remaining

in the paint containers. The consistency should

correspond to that of water.

Note: If the paint used does not cover well, in-

crease the amount of paint in the mixture ratio.

Turning airbrush compressor

on / oﬀ

Turn the airbrush compressor

on by setting the

on / oﬀ switch

to the position “I“ (see Ill. C).

Turn the airbrush compressor

oﬀ by setting

the on / oﬀ switch

in the position “0“ (see

Ill. C).

Note: Full pressure is built up after two seconds.

Regulating the air pressure

Regulate the air pressure by actuating the vent

of the air blow gun

to more or less of an

extent.

ATTENTION! The device has a pressure switch,

which periodically and automatically turns the de-

vice oﬀ if there is excess pressure or if it is not in use.

Shortly before reaching the switch-oﬀ point, the

compressor runs more roughly and vibrates. This

may also be the case when re-started under load.

The performance and functionality are not impaired

by this. This is not a defect, rather, serves to protect

the compressor from overloading.

Regulating the spraying results

Regulate the amount of the paint supplied by

turning the paint nozzle of the spray stylus to

the right or left (see Ill. B).

Using the accessories (see Ill. D)

Air mattress adapter

, ball needle

Use a pipe wrench to unscrew the nozzle

9 a

the air blow gun

Then – depending on what is needed – screw

on the air mattress adapter

or the ball

89068_par_Airbrush_Set_Content_LB2.indd 40 04.06.13 09:56

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 89068 PABK 60 A1 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,41 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside IAN 89068 PABK 60 A1 Manual

Product: