745111
41
Zoom out
Zoom in
Previous page
1/44
Next page
41 GB
Commissioning / Possible applications / After initial use
After initial use / Maintenance / Cleaning and care / Troubleshooting
Be careful when putting down
the device. Always put down the equipment so
it does not come into contact with the trigger.
This could potentially result in accidental activa-
tion of the equipment, which again could result
in hazards.
Maintenance
ATTENTION! All maintenance must be per-
formed by trained individuals. Following the
specified maintenance instructions ensures a
long service life and proper operation of this
quality product.
Disconnect equipment from the compressed air
source when performing maintenance and care.
Check the condition of wear and tear items
and accessories with every maintenance.
Note: Daily cleaning and regular lubrication
are absolutely required for smooth operation.
Only use special tool oil.
No maintenance is required beyond the above
mentioned lubrication and cleaning.
Cleaning and Care
Only use a dry cloth to clean the multitool.
Never clean with liquids such as petrol, sol-
vents or water.
Do not allow liquids to enter the equipment.
Use a vacuum cleaner to remove abrasive dust
or sawing debris from the equipment.
For oiling you may use one of the follow-
ing options
Note: If available, you may use an in-line a line
oiler, -trap or an entire maintenance unit as shown
above. We highly recommend using such mainte-
nance accessories.
a) via oil-mist lubricator
A complete maintenance unit includes an oil-mist
lubricator and is attached to the compressor
b) via line lubricator
A line lubricator is installed within close proxim-
ity of the tool (approx. 50 cm away) which ad-
equately supplies the equipment with oil.
c) manually
If your equipment (or your compressed air sys-
tem) features neither a maintenance unit nor a
line lubricator you must add 3–5 drops of oil
to the compressed air connection before each
use. If the air tool has not been used for several
days you must add 5–10 drops of oil to the
compressed air connection before powering
on the equipment.
Always store your air tools / equipment and ac-
cessories in dry locations.
Troubleshooting
Note: Regular lubrication is imperative to ensure
the longest possible life for your compressed air de-
vice. We recommend continuous lubrication via in-
line oil-mist equipment.
Fault Reduced performance
Cause Solution
1. Insufficient pres-
sure
Check all connections and
verify your compressor is
supplying sufficient pressure.
2. Clogged line Clean the line.
3. Improper lubri-
cation or insufficient
lubricant
Lubricate equipment as in-
structed.
4. Blunt or dam-
aged accessory
Replace accessory.
5. Leak / Leaking
connection
Use teflon tape or replace
the defective part.
6. Contaminated
mechanism
Have your equipment
cleaned by a qualified
technician.
73791_Druckluft-Multitool_content_LB1 (nur NL).indd 41 11.05.12 17:56
41


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 73791 PDMT 6.2 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 73791 PDMT 6.2 A1 in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 3,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info