Manual Parkside IAN 73791 PDMT 6.2 A1 (page 40 of 44) (English, German, Dutch)

745111

Zoom out

Zoom in

1/44

40 GB

Commissioning / Possible applications / After initial use

Step 1:

Insert the selected tool into the intake of the com-

pressed air multitool. You may adjust the accessory

to the desired alignment in 30° increments using

the 4 setting pins (see Fig. C).

Step 2:

First place the washer

onto the accessory (see

Fig. D) and then place the tension ring

over it

(see Fig. E).

Step 3:

Now take the Allen screw

and tighten using the

included Allen key

. Use the counter wrench

to ﬁx the appliance while tightening the Allen

screw

(see Figs. F and G). Your accessory is

now correctly attached.

ATTENTION! Verify the screw is tight and has

no play. The loose accessory will otherwise

pose a risk of injury during use.

ATTENTION! During use be sure only to bring

the equipment into contact with the material to

be processed once it has reached suﬃciently

high speed. Putting the equipment on the mate-

rial and then switching it on is dangerous and

may result in injury.

Verify the equipment is correctly connected

and the connecting hose properly seated.

Use the pressure applied to the trigger to control

the speed of the equipment. Hold the equipment

with both hands during use to allow for safe

control of the tool without slipping (Fig. K).

Note: Applying light pressure to the surface

to be worked on will suﬃce.

Pull the trigger

to start the equipment.

Release the trigger

to stop the equipment.

Possible applications

Using the sanding attachment

(see Fig. I, J)

Attach the sanding attachment

as described

in Chapter “Attaching accessories”, but without

using the washer

Select the correct sandpaper for your applica-

tion (coarse / medium / ﬁne)

and

press onto the hook-and-loop pad of the sand-

ing attachment.

Be sure the sandpaper is centred and pro-

trudes as little as possible on all sides.

Using the scraper attachment

(see Fig. K)

The two scraper attachments

can be

used to remove stubborn materials from surfaces.

Use either the straight

or the curved

scraper attachment. The latter with its curved

blade ensures there is some distance between

the material and the equipment.

Using the saw attachments

(see Fig. L)

Use the included saw attachments (

)

to cut up to 3 cm deep into wooden materials.

The manufacturer prohibits cutting any other

materials as the attachments are not designed

for this purpose, thus posing the risk of dam-

age or injuries.

When using these attachments pay particular

attention to handling the equipment safely with

both hands. Never apply high pressure or posi-

tion your hand where it can easily slip oﬀ.

CAUTION! DANGER WHEN

SAWING! Keep hands away from

the area of the saw blade. Do not

reach below the work piece and never adjust it

with the hand within the area of the cut. Contact

with the saw blade may result in injury.

After initial use

Once the task has been ﬁnished the equipment

must be disconnect from the compressed air supply.

Brieﬂy activate the trigger on the equipment to

release any compressed air remaining in the

equipment.

First pull back on the lock

(see Fig. M).

Then remove the coupling

(see Fig. N).

After initial use / Maintenance / Cleaning and care / Troubleshooting

73791_Druckluft-Multitool_content_LB1 (nur NL).indd 40 11.05.12 17:56

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 73791 PDMT 6.2 A1 in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 3,34 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside IAN 73791 PDMT 6.2 A1 Manual

Product: