Manual Parkside IAN 73782 PDT 40 B2 (page 34 of 37) (English, German, Dutch, French)

745069

Zoom out

Zoom in

1/37

34 GB

Maintenance and cleaning / Service / Warranty / DisposalOperation / Maintenance and cleaning

provide any performance increase, but only in-

creases compressed air consumption and ac-

celerates wear on the device.

Switch on the compressor.

Allow the compressor to run once long enough

until maximum tank pressure is reached and the

device is switched oﬀ.

Place the compressed air tacker on the workpiece

and press the trigger

NOTE: The compressed air tacker

is equipped with a trigger lock

The fastener will only leave the device

when the mouth of the compressed air tacker is

pressed against the workpiece and the trigger

is actuated.

Check that the fastener has been driven in cor-

responding to the work requirements.

– If the fastener is protruding, increase the air

pressure in 0.5 bar increments.

– If the fastener is too deep, decrease the air

pressure in 0.5 bar increments.

As an alternative, you can accelerate the work

by keeping the trigger

depressed.

Set the compressed air tacker against the work-

piece.

Press the device against the workpiece until the

mouth

touches it. The fastener will leave the

device.

As long as the trigger

is kept depressed, each

time the mouth

touches the workpiece one

fastener will leave the device.

Another alternative is to keep the mouth

pressed against the workpiece.

Each time the trigger

is actuated, a fastener

will leave the device.

NOTE: Fine adjustment with the knurled screw

is possible.

Turn the knurled screw

downwards in order

to drive the fastener more deeply into the work-

piece.

Turn the knurled screw

upwards in order to

drive the fastener less deeply into the workpiece.

Turn the exhaust air aperture

to guide the

exhaust airﬂow in the desired direction.

After ﬁnishing work, disconnect the device from

the compressor.

Removing jammed fasteners

If a staple or nail gets jammed in the magazine

slot, immediately disconnect the compressed

air supply.

Open the magazine

as described in the

chapter “Loading the magazine“.

Open the face plate

by pulling the face

plate quick clamping lever

in the direction

of the trigger lock

Remove the jammed fastener.

Close the face plate

by pulling the face

plate quick clamping lever

in the direction

of the exhaust air aperture

Close the magazine

of the compressed air

tacker as described in the chapter “Loading the

magazine“.

Maintenance and cleaning

RISK OF INJURY! Be absolutely certain to

disconnect the device from the compressed air

source before cleaning or maintaining it.

Maintenance

Lubrication with oil mister

NOTE: As a treatment stage after the pressure re-

ducer, an oil mister provides continuous and opti

mum

lubrication of the compressed air tacker. An oil mis-

ter gives oﬀ ﬁne drops of oil into the airﬂow and so

guarantees regular lubrication.

Install the oil mister after the (ﬁlter) pressure re-

ducer. To do so, insert the nipple of the oil mis-

ter into the quick-release coupling of the (ﬁlter)

pressure reducer.

Then connect the compressed air device to the

quick-release coupling provided for it.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 73782 PDT 40 B2 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,68 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside IAN 73782 PDT 40 B2 Manual

Product: