Manual Parkside IAN 73782 PDT 40 B2 (page 33 of 37) (English, German, Dutch, French)

745069

Zoom out

Zoom in

1/37

33 GB

Safety of the fastener driving tool / Preparing the product for use / Operation

When loosening the hose coupling, hold the

hose ﬁrmly in your hand to prevent injuries

caused by a rebounding hose.

Be absolutely certain to use a ¼‘„ threaded

nipple and a quick-release coupling for the

compressed air connection.

Never place your hands near the mouth when

the device is ready to operate. Otherwise inju-

ries may result.

Pay attention to damage. Check the de-

vice for damage before bringing it into use. If

the device exhibits defects, it must not be oper-

ated under any circumstances.

Do not use any pointed objects. Never

insert pointed and / or metal objects into the

inside of the device.

Original accessories / tools

Use only the accessories and attachment

detailed in the operating instructions.

The use of fasteners or other accessories other

than those recommended in the operating in-

structions could lead to you suﬀering an injury.

Preparing the product for use

NOTE: always wear the protective goggles sup-

plied before putting the tool into operation. Remove

the protective ﬁlm from the protective goggles before

using for the ﬁrst time.

Connecting the compressed

air source

NOTE: The compressed air tacker must only be

operated with cleaned, oil-misted compressed air

and must not exceed the maximum operating pres-

sure of 8 bar. The compressor must be ﬁtted with a

pressure reducer in order to regulate the operating

pressure.

Connect the device to a suitable compressed

air source.

1. To do so, press the compressed air hose quick-

release coupling (not included in the scope of

delivery) on the ¼“ threaded nipple

of the

compressed air tacker.

Locking is automatic.

2. Connect the other end of the compressed air

hose to the (ﬁlter) pressure reducer on the com-

pressor.

Loading the magazine

1. Press the magazine lever

and pull the mag-

azine cover back to its stop position.

2. Insert the corresponding fastener (nails, see

Fig. 01 or staples, see Fig. 02) into the maga-

zine

3. Slide the magazine cover forwards until it locks.

Operation

Load the magazine

of the compressed air

tacker as described in the chapter “Loading the

magazine“.

Use the pressure reducer to set the correct

operating pressure.

Ensure that the permissible operating pressure

of 8 bar at the device is never exceeded.

Operating pressure that is too high does not

Safety of the fastener driving tool

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 73782 PDT 40 B2 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,68 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside IAN 73782 PDT 40 B2 Manual

Product: