Manual Parkside IAN 311903 PWS 230 C3 (page 27 of 109) (English, German, Dutch, French, Polish)

749297

Zoom out

Zoom in

1/109

PWS 230 C3 GB│IE │ 23 ■

Special safety instructions for

grinding and abrasive cutting

a) Use only the grinding accessories approved

for your power tool and the appropriate

blade guard for these grinding tools. Grind-

ing tools that are not designed for the power

tool cannot be suﬃciently shielded and are

unsafe.

b) Oﬀset grinding discs must be ﬁtted so that the

grinding surface does not protrude over the

level of the blade guard edge. An improperly

ﬁtted grinding disc which protrudes over the

level of the blade guard edge cannot be prop-

erly guarded.

c) The blade guard must be securely mounted

on the power tool and adjusted to ensure

maximum safety so that the smallest possible

amount of the grinding tool is open to the op-

erator. The blade guard is designed to protect

the operator from fragments, accidental contact

with the grinding tool and sparks that could

ignite clothing.

d) Grinding tools should only be used for the

recommended applications.

For example: Never grind with the side

surface of a cutting disc. Cutting discs are de-

signed to remove material with the edge of the

disc. Any lateral application of force on these

grinding tools can lead to breakage.

e) Always use an undamaged clamping ﬂange

of the correct size and shape for the selected

grinding disc. Suitable ﬂanges support the

grinding disc and reduce the risk of disc break-

age. Flanges for cutting discs can be diﬀerent to

ﬂanges for other grinding discs.

f) Do not use worn grinding discs from larger

power tools. Grinding discs for larger power

tools are not designed for the higher rotational

speeds of smaller power tools and can break.

Additional special safety instructions

for abrasive cutting

a) Avoid causing blockages to the cutting disc

or high contact pressure. Do not make any

excessively deep cuts. Overloading the cutting

disc increases the stress and likelihood of tilting

or jamming and thus the possibility of kickback

or breakage of the grinding tool.

b) Avoid the area in front of and behind the

rotating cutting disc. When you move the cut-

ting disc away from yourself in the workpiece,

it is possible, in the event of a kickback, that the

power tool along with the rotating disc might be

thrown out directly towards you.

b) If the cutting disc jams or you stop working,

switch the tool oﬀ and hold it steadily in

the workpiece until the disc has completely

stopped turning. Never attempt to pull a ro-

tating cutting disc out of a cut. This could lead

to kickback. Identify and remove the cause of

the jam.

d) Do not switch the power tool back on while

it is located in the workpiece. Allow the cut-

ting disc to reach its full speed before you

carefully continue the cut. Otherwise, the disc

can jam, jump out of the workpiece or cause

kickback.

e) Support boards or large workpieces to re-

duce the risk of the cutting disc jamming and

causing a kickback. Large workpieces can

bend under their own weight. The workpiece

must be supported on both sides of the disc:

both in the vicinity of the cutting disc and also

at the edge.

f) Be particularly careful when making "pocket

cuts" into existing walls or other obscured

areas. The inserted cutting disc may cut into

gas or water pipes, electrical wiring or other

objects that can cause kickback.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 311903 PWS 230 C3 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 1,79 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside IAN 311903 PWS 230 C3 Manual

Product: