Manual Parkside IAN 311314 PGI 1200 A1 (page 10 of 48) (English, German, Dutch, French)

749335

Zoom out

Zoom in

1/48

5GB/IE/NI

Engine oil 0.25 l

(15W-40)

Use at ⅔ engine load approx. 0.88 l/h

Weight 12.8 kg

Sound pressure level LpA 74.39 dB (A)

Sound power level LWA 95 dB(A)

Uncertainty K 1.07 dB (A)

Power factor cos ϕ 1

Performance class G1

Quality class B

Spark plug MS A7RTC

Operating mode S1 (long use)

The machine can be used continuously with the indicated

power.

Operating mode S2 (Short term use)

The machine can be used in the short term with the indicated

power.

Acceptable ambient temperature:

-10 to +40 °C

Height: 1000 m above NN

rel. air humidity: 90 % (not condensed)

7. Before starting the equipment

• Open the packaging and remove the device carefully.

• Remove the packaging material as well as the packaging

and transport bracing (if available).

• Check that the delivery is complete.

• Check the device and accessory parts for transport dam-

age.

• If possible, store the packaging until the warranty period

has expired.

ATTENTION

The device and packaging materials are not toys!

Children must not be allowed to play with plastic

bags, ﬁlm and small parts! There is a risk of swal-

lowing and suﬀocation!

Installation (Fig. 1/2)

To attach the handle (1), remove both Phillips screws M6x35

mm which are inserted. Place the handle (1) in position and

screw it tight. Attach all parts before pouring in fuel or oil in

order to prevent leaking of liquids.

Electrical safety

Prior to use, the generator and its electrical equipment (includ-

ing lines and plug connectors) should be checked to ensure

that there are no defects.

Never connect the generator to the mains (power point).

Keep the cables as short as possible.

Earthing (Fig. 1)

Earthing is needed to disperse static discharge. Connect a ca-

ble from one side of the earthing connector (7) of the generator

and from the other side to an external ground.

ATTENTION! When being used for the ﬁrst time, motor oil

(15W-40, approx. 0.25 l) and petrol (unleaded normal petrol)

must be put in.

Check the fuel level and the oil, and if necessary top them

up. Make sure you have adequate ventilation. Ensure that the

spark cable is securely in the spark plug. Unplug any electric

device connected to the generator.

Putting in oil (Fig. 5)

Put the generator with its front side down and unscrew the oil

ﬁller plug (13). Pour in 0.25 litres of engine oil (15W-40).

Close the oil ﬁller cap (13) and stand the generator upright

Putting in fuel (Fig. 1/7)

Keep away from ignition sources! Always refuel in well-ventilat-

ed rooms or outside. Open the fuel tank cap (2) and, using a

ﬁller pipe (not included in delivery), pour in a maximum of 4.2

litres of unleaded fuel into the fuel container. Ensure the tank

level is not exceeded and no fuel is spilled. Use the fuel ﬁlter.

Clean up spilled fuel immediately and wait until the fuel fumes

have evaporated (ﬁre hazard). Close the fuel tank cap (2).

8. Operation

Start the engine (Fig. 1/3/6)

ATTENTION! When starting with the express start (10) you

can injure your hand with the sudden kick back.

Wear protective gloves when starting.

• Open the petrol tap (17) by turning the tap downwards.

• Put the on / oﬀ switch (6) to the “on” position. Turn the choke

lever (9) to I I (in the left position).

• Start the engine with the express start (10) by sharply pull-

ing the handle. If the engine has not started pull the handle

again.

• Push the choke lever (9) back once the engine has started

(in the right position).

• Connect the device to the 230 V∼ socket (8).

ATTENTION! This socket can be loaded continuously (S1)

with 1000 W and short term (S2) for a maximum of 5 seconds

with 1200 W.

Note: Some electric devices (sabre saws, drills etc.) can use

more electricity when doing heavy duty tasks.

Storing the engine (Fig. 1/6)

Before putting away, let the generator run without load so that

the device can „cool down“.

• Turn the on / oﬀ switch to the „OFF“ position.

• Close the petrol tap.

Overload protection 230 V∼ socket

NOTE! This generator is ﬁtted with an overload protector.

This cuts oﬀ the sockets.

Green operating bulb:

Flashes 1 x per interval Speed too low

Flashes 2 x per interval Temperature too high

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 311314 PGI 1200 A1 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 4,43 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside IAN 311314 PGI 1200 A1 Manual

Product: