749299

Parkside IAN 310850 PISG 120 A1 Manual

28
Zoom out
Zoom in
Previous page
1/76
Next page
28 GB/IE
Only have work to the mains
voltage end, e.g. to cables,
plugs, outlets, etc. performed
by a electrically skilled person
in accordance with national
and local regulations.
In the event of an accident,
immediately disconnect the
welding equipment from the
mains voltage.
If electrical contact voltage
occurs, immediately switch
the equipment off and have
it inspected by an electrically
skilled person.
Always ensure good electrical
contacts on the welding cur-
rent end.
Always wear insulating gloves
on both hands whilst welding.
These will protect from electric
shock (no-load voltage of the
welding current), from hazard-
ous rays (heat and UV rays)
and glowing metal and weld
splashes.
Wear solid, insulating shoes.
The shoes should also insulate
when exposed to moisture.
Low shoes are not suitable, as
glowing metal drops falling
could cause burns.
Wear suitable protective cloth-
ing, no synthetic garments.
Do not look into the arc with
unprotected eyes, only use a
welding shield with approved
protective glass per DIN. In
addition to light- and heat rays
which could result in blinding
or burns, the arc also emits UV
rays. Without adequate pro-
tection, this invisible ultraviolet
radiation causes very painful
conjunctivitis which is only
noticed a few hours later. UV
rays further cause burns simi-
lar to a sunburn in unprotected
areas of the body.
Persons near the arc or assis-
tants must also be informed of
the risks and outfitted with the
necessary protection. If neces-
sary, set up protective panels.
Ensure an adequate supply of
fresh air whilst welding, par-
ticularly in small spaces, as it
produces smoke and harmful
gasses.
Do not weld containers in
which gasses, fuels, mineral
oils, etc. were stored - even if
emptied a long time ago - as
residue poses an explosion
hazard.
Special regulations apply in
rooms posing fire- and explo-
sion hazards.
Welded joints exposed to
great strain and needing to
meet certain safety require-
Safety instructions
… 28 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 310850 PISG 120 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 310850 PISG 120 A1 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info