Manual Parkside IAN 303408 PBS 350 A1 (page 23 of 72) (English, German, Dutch, French)

748151

Zoom out

Zoom in

1/72

16 GB/IE

insofar as nothing different is speciﬁed in the operating

manual.

- Damaged switches must be replaced at a customer ser-

vice workshop.

- Do not use any faulty or damaged connection cables.

- Do not use any electric tool on which the switch cannot

be switched on and off.

21. ATTENTION!

- The use of other insertion tools and other accessories

can entail a risk of injury.

22. Have your electric tool repaired by a qualiﬁed electri-

cian

- This electric tool conforms to the applicable safety reg-

ulations. Repairs may only be performed by an elec-

trician using original spare parts. Otherwise accidents

can occur.

Additional safety instructions

• Wear safety gloves whenever you carry out any mainte-

nance work on the blade!

• When cutting round or irregularly shaped wood, use a

device to stop the workpiece from twisting.

• When cutting boards in upright position, use a device to

prevent kick-back.

• A dust extraction system designed for an air velocity of 20

m/s should be connected in order to comply with wood-

working dust emission values and to ensure reliable op-

eration.

• Give these safety regulations to all persons who work on

the machine.

• Do not use this saw to cut ﬁre wood.

• The machine is equipped with a safety switch to prevent it

being switched on again accidentally after a power fail-

ure.

• Before you use the machine for the ﬁrst time, check that

the voltage marked on the rating plate is the same as your

mains voltage.

• If you use a cable reel, the complete cable has to be

pulled off the reel.

• Persons working on the machine should not be distracted.

• Note the direction of rotation of the motor and blade.

• Never dismantle the machineʼs safety devices or put them

out of operation.

• Never cut workpieces which are too small to hold securely

in your hand.

• Never remove loose splinters, chips or jammed pieces of

wood when the saw blade is running.

• It is imperative to observe the accident prevention regula-

tions in force in your area as well as all other generally

recognized rules of safety.

• Note the information published by your professional as-

sociations.

• Adjustable protective devices have to be adjusted as close

as possible to the workpiece.

• Important! Support long workpieces (e.g. with a roller ta-

ble) to prevent them sagging at the end of a cut.

• Make sure the blade guard (4) is in its lower position when

the saw is being transported.

• Safety guards are not to be used to move or misuse the

machine.

- An additional support is necessary for long workpieces

(table, trestle, etc.) in order to prevent the machine from

tipping over.

- Always press the workpiece ﬁrmly against the working

plate and stop in order to prevent bouncing and twist-

ing of the workpiece.

13. Avoid abnormal posture

- Make sure that you have secure footing and always

maintain your balance.

- Avoid awkward hand positions in which a sudden slip

could cause one or both hands to come into contact

with the saw blade.

14. Take care of your tools

- Keep cutting tools sharp and clean in order to be able

to work better and more safely.

- Follow the instructions for lubrication and for tool re-

placement.

- Check the connection cable of the electric tool regu-

larly and have it replaced by a recognised specialist

when damaged.

- Check extension cables regularly and replace them

when damaged.

- Keep the handle dry, clean and free of oil and grease.

15. Pull the plug out of the outlet

- Never remove loose splinters, chips or jammed wood

pieces from the running saw blade.

- During non-use of the electric tool or prior to mainte-

nance and when replacing tools such as saw blades,

bits, milling heads.

- When the saw blade is blocked due to abnormal feed

force during cutting, turn the machine off and discon-

nect it from power supply. Remove the work piece and

ensure that the saw blade runs free. Turn the machine

on and start new cutting operation with reduced feed

force.

16. Do not leave a tool key inserted

- Before switching on, make sure that keys and adjusting

tools are removed.

17. Avoid inadvertent starting

- Make sure that the switch is switched off when plug-

ging the plug into an outlet.

18. Use extension cables for outdoors

- Only use approved and appropriately identiﬁed ex-

tension cables for use outdoors.

- Only use cable reels in the unrolled state.

19. Remain attentive

- Pay attention to what you are doing. Remain sensible

when working. Do not use the electric tool when you

are distracted.

20. Check the electric tool for potential damage

- Protective devices and other parts must be carefully in-

spected to ensure that they are fault-free and function

as intended prior to continued use of the electric tool.

- Check whether the moving parts function faultlessly

and do not jam or whether parts are damaged.

All parts must be correctly mounted and all conditions must

be fulﬁlled to ensure fault-free operation of the electric tool.

- The moving protective hood may not be ﬁxed in the

open position.

- Damaged protective devices and parts must be prop-

erly repaired or replaced by a recognised workshop,

Hallo sehr geehrte Damen und Herren, ich suche einen Ersatz für die Bandsäge.
Einmal das Sägeblatt und zum anderen Die Bandauflage für die zwei Rollen.
Vielen Dank im Voraus. Submitted on 19-7-2022 at 10:02
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 303408 PBS 350 A1 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,05 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside IAN 303408 PBS 350 A1 Manual

Product: