748020

Parkside IAN 295715 PFS 710 D3 Manual

20
Zoom out
Zoom in
Previous page
1/74
Next page
PFS 710 D3
GB
│
IE 
│
 17 ■
Plunge sawing:
CAUTION! RISK OF KICKBACK!
■ Plunge cuts may only be made in soft
materials (wood or similar).
Proceed as follows:
1. Place the sabre saw with the lower edge of the
footplate onto the workpiece. Switch the
appliance on.
2. Tilt the sabre saw forwards and plunge the saw
blade into the workpiece.
3. Position the sabre saw vertically and continue
sawing along the cutting line.
Maintenance and cleaning
WARNING! RISK OF INJURY!
Always switch the appliance off
before carrying out any work on it.
■ Always remove the power plug from the power
socket before cleaning the appliance.
■ Replace the saw blade as soon as its teeth are
blunt and proper sawing is therefore no longer
possible.
■ Keep the appliance and ventilation slits clean at
all times. If the ventilation slits are blocked, there
is a risk of overheating and/or the appliance
being damaged.
■ Always clean the appliance after completion
of work.
■ Never permit liquids to enter inside the appli-
ance. Use a cloth to clean the housing. Never
use petrol, solvents or cleansers which can
damage plastic.
■ If necessary, clean the saw blade mount with a
brush or compressed air.
Kompernass Handels GmbH
warranty
Dear Customer,
This appliance has a 3-year warranty valid from
the date of purchase. If this product has any faults,
you, the buyer, have certain statutory rights. Your
statutory rights are not restricted in any way by the
warranty described below.
Warranty conditions
The validity period of the warranty starts from the
date of purchase. Please keep your original receipt
in a safe place. This document will be required as
proof of purchase.
If any material or production fault occurs within
three years of the date of purchase of the product,
we will either repair or replace the product for you
at our discretion. This warranty service is dependent
on you presenting the defective appliance and
the proof of purchase (receipt) and a short written
description of the fault and its time of occurrence.
If the defect is covered by the warranty, your product
will either be repaired or replaced by us. The repair
or replacement of a product does not signify the
beginning of a new warranty period.
Warranty period and statutory claims for
defects
The warranty period is not prolonged by repairs
effected under the warranty. This also applies to
replaced and repaired components. Any damage
and defects present at the time of purchase must
be reported immediately after unpacking. Repairs
carried out after expiry of the warranty period shall
be subject to a fee.
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 295715 PFS 710 D3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 295715 PFS 710 D3 in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 1,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info