Manual Parkside IAN 292167 PDSS 16 A1 (page 20 of 90) (English, German, Dutch, French, Portuguese, Spanish)

746866

Zoom out

Zoom in

1/90

PDSS 16 A1

│

17 ■

■ The permissible speed of the accessory tool

used must be at least as high as the maximum

speed speciﬁed for the compressed air tool. Ac-

cessories that rotate faster than the permissible

rate can break and throw pieces into the air.

■ Wear a safety helmet for overhead work.

■ The tool will run on after the compressed air

tool has been switched oﬀ.

■ Ensure that no hazard is caused by sparks cre-

ated during use. Explosive or ﬂammable dusts

can be generated when processing certain

materials. There is a risk of explosion or ﬁre.

Hazards caused by repetitive move-

ments

■ Users of the compressed air tool may experi-

ence unpleasant sensations in their hands, arms,

shoulders, neck area or other body parts.

■ Assume a comfortable position when working

with the compressed air tool, pay attention to

safe footing and avoid unfavourable positions

or such that make it diﬃcult to keep your bal-

ance. During work over longer periods, the

operator should change posture to avoid dis-

comfort and fatigue.

■ If the operator notices symptoms such as persis-

tent discomfort, throbbing, pain, tingling, burning

or stiﬀness, these warning indications should not

be ignored. The operator should consult a quali-

ﬁed medical doctor.

Hazards caused by accessories

■ Separate the compressed air tool from the com-

pressed air supply before replacing the attach-

ment or accessory.

■ Only use accessories that are intended for this

appliance and comply with the requirements

and speciﬁcations listed in these operating

instructions.

■ Avoid direct contact with the accessory tool

during and after use because it may be hot or

have sharp edges.

■ The permissible speed of the accessory tool

used must be at least as high as the maximum

speed speciﬁed for the compressed air tool. Ac-

cessories that rotate faster than the permissible

rate can break and throw pieces into the air.

■ Never ﬁt a grinding disc, cutting disc or milling

cutter. A bursting grinding disc can lead to seri-

ous injuries or death.

■ Do not use discs that are damaged, cracked or

have been dropped.

■ Only approved accessory tools with the appro-

priate shaft diameter may be used.

■ Observe the manufacturer's recommendation

for small grinding tools. The maximum permissi-

ble protrusion (L0 = length of the shaft between

the collet chuck end and the small grinding

tool) speciﬁed by the manufacturer must not be

exceeded when using small grinding tools! If

the protrusion (L0) is increased, the permissible

rotation speed must be lowered. Wherever pos-

sible, insert the complete length of the shaft of

the accessory tool into the collet chuck. Ensure

that the clamping length (Lg) is at least 10 mm.

■ The shaft diameter of the accessory tool must

exactly match the clamp bore of the collet

chuck!

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 292167 PDSS 16 A1 in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 3,09 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside IAN 292167 PDSS 16 A1 Manual

Product: