746867
25
Zoom out
Zoom in
Previous page
1/116
Next page
2 5
I EG B
5. In order to fasten the selected
sharpener in the working posi-
tion, from above push this into the
guide rails. Press the sharpener
down until it snaps into place.
The sharpeners also present a
safety device. Never use this
device without a sharpener.
Risk of injury!
Operation
Caution! Risk of injury!
- Always disconnect the plug from
the mains socket before working.
- Use only grinding disks and acces-
sories recommended by the manu-
facturer. The use of other insertion
tools and other accessories may
cause risk of injury.
- Never operate the device without
the visual protection disk.
- Switch on the equipment only
when it is safely installed on the
work surface.
Despite spark protection, al-
ways wear safety goggles
while working in order to
avoid eye injuries.
Keep your hands away from
the grinding wheel and grind-
ing belt when the device is in
operation. Injury hazard.
Switching on and off
Ensure that the mains voltage match-

plate.
Connect the equipment to the mains.
1. To switch on, press the I On switch
and the device starts up (see 3).
2. To switch off, press the 0 off switch
and the device switches off (see 3).
After switching on the device, wait until the

then must you start with the grinding.
The disk will continue to
run after the equipment is
switched off. There is a risk
of injury.
Test run:
Before starting work and after each
change of grinding disk, carry out a test
run of at least 60 seconds with no load.
Switch off the equipment immediately if the
disk runs lumpy, substantial vibrations oc-
cur, or abnormal noises are generated.
Sharpening drills
Drills with a diameter of 3-10 mm can be
sharpened.
1. Mount the selected sharpener
(see Mounting sharpener).
2. Remove the drill holder (14) from
the sharpener.
3. Insert the drill into the drill holder
(14). Do not attach the drill.
4. Insert the drill holder (14) up-
wards into the adjusting device
(15) using the knurled nut for
drill-fastening (12).
5. Push the drill to the front into the
V-nut up to the metal stop. The

closely to the metal surfaces.
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 291715 PSS 65 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 291715 PSS 65 A1 in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 3,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info