746421
20
Zoom out
Zoom in
Previous page
1/74
Next page
PTBS 520 A1
GBIE 17
Using the magazine attachment
Setting the screw length:
Undo the screw
.
Set the required screw length using the screw
.
Position the locking tab in the provided slot for
the required screw length.
Retighten the screw .
40/41
35
30
25
Setting the screw-in depth:
Set the required screw-in depth using the
screw
.
You can work out the required screw-in depth
by trial and error.
Surface
Level
NOTE
Check the direction of rotation before starting
work. The magazine attachment
may
only be used when the direction is set to
"clockwise" (see section "Setting the rotation
direction").
Screwing in screws:
Always apply the magazine attachment
to
the workpiece at right angles. The screw stop
must be over the screwing location.
Switch on the device on switch
.
Apply even pressure to the workpiece until the
screw is screwed in.
Raise the screw stop
briefly so that it jumps
back to its starting position. The next screw is
transported into the working position when it is
actuated again.
As soon as the screw-in depth is reached, the
drive disengages and the screw bit stops
turning.
NOTE
Screws which have already been screwed in
cannot be unscrewed or tightened with the
magazine attachment
fitted.
To do this, remove the magazine attachment
and use the depth stop sleeve
.
Using the depth stop sleeve
The depth stop sleeve allows you to determine
the screw-in depth of screws.
Setting the screw-in depth:
Turn the adjusting ring
clockwise (seen from
your working position) to reduce the screw-in
depth.
Turn the adjusting ring
anticlockwise (seen
from your working position) to increase the
screw-in depth.
You can work out the required setting by trial
and error.
Screwing in screws:
Place the screw bit
and the bit adapter
on the screw.
Press the screw against the workpiece.
Switch the appliance on.
Screw the screw into the workpiece until the
preset screw-in depth is reached.
As soon as the screw-in depth is reached, the
drive disengages and the screw bit
stops
turning.
Check the screw-in depth.
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 285766 PTBS 520 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 285766 PTBS 520 A1 in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 0,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info