746434
21
Zoom out
Zoom in
Previous page
1/80
Next page
PDT 40 D3
GB
IE
 17
Check whether the fastener is properly driven in
according to requirements.
If the fastener protrudes, increase the air
pressure in steps of 0.5 bar.
If the fastener is too deep, reduce the air
pressure in steps of 0.5 bar.
Alternatively, you can speed up the work, by
holding in the trigger
.
Apply the compressed air stapler to the work-
piece.
Press the appliance onto the workpiece till the
opening
is touching it. The fastener material
leaves the appliance.
As long as you pull the trigger
a piece of
fastener material leaves appliance each time
the opening touches the workpiece.
Alternatively, you can keep the opening
of
the appliance permanently pressed onto the
workpiece.
Each time you pull the trigger
a fastener
leaves the appliance.
NOTE
Fine adjustment is also possible with the
knurled screw
.
Turn the knurled screw
down to sink the
fastener deeper into the workpiece.
Turn the knurled screw
up to sink the fastener
less deeply into the workpiece.
Turn the exhaust cover
to direct the escaping
air in the desired direction.
Disconnect the appliance from the compressor
after completing your work.
Removing jammed staples
If a staple/nail gets stuck in the magazine shaft, im-
mediately remove the compressed air supply line.
Open the magazine
as described in the
section "Filling the magazine".
Open the face plate
by pulling the face
plate quick release lever in the direction of
the trigger lock .
Remove the food.
Close the face plate
by pulling the face
plate quick release lever in the direction of
the exhaust panel .
Close the magazine
of the compressed air
stapler, as described in the section "Filling the
magazine".
Maintenance and cleaning
WARNING! RISK OF INJURY!
Disconnect the appliance from the
compressed air supply.
WARNING!
Have the power tool repaired by the Service
Centre or a qualified technician and only
using genuine replacement parts. This will
ensure that the safety of the appliance is
maintained.
CAUTION!
Any service or repair work over and above
that described in this section may only be
carried out by specialists.
Maintain the compressor tool regularly to ensu-
re safe operation.
Check bolted connections for a tight fit, retigh-
ten if necessary.
We recommend fitting a pressure reducer with
a water separator and an oiler in front of the
compressed air tool.
If there is increased oil or air discharge, check
the compressed air tool and have it serviced if
necessary.
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 285202 PDT 40 D3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 285202 PDT 40 D3 in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 1,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info