Manual Parkside IAN 285202 PDT 40 D3 (page 20 of 80) (English, German, Dutch, French, Portuguese, Spanish)

746434

Zoom out

Zoom in

1/80

PDT 40 D3

■ 16

│

Before use

NOTE

► Put on the supplied protective goggles before

each use. Remove the protective ﬁlm from the

goggle lenses before ﬁrst use.

Connecting the compressed air supply

NOTE

► In order to achieve the full power available

from your compressed air tool, always use

compressed air hoses with an internal diame-

ter of at least 9 mm. A lower internal diameter

can considerably reduce the power.

► The appliance may be operated only with

cleaned, atomised-oil air and must not exceed

the maximum working pressure of 8 bar on

the appliance. The compressor must be ﬁtted

with a pressure reducer to regulate the

working pressure.

CAUTION!

► Do not use a compressed air line that contains

any condensate.

► The tool must be suﬃciently supplied with

pneumatic oil to ensure long service life. This

can take place as follows:

– Use oiled compressed air by ﬁtting a mist

lubricator.

– Without a mist lubricator: Add oil ma-

nually via the threaded nipple

every

day. Approx. 1–2 drops of pneumatic

oil for every 15 operating minutes during

continuous use.

► If the tool has been out of operation for sever-

al days, add around 5 drops of pneumatic oil

manually via the threaded nipple

♦ Connect the appliance to a suitable compressed

air source.

♦ 1.) For this purpose, press the quick-release

connection of the compressed air hose (not

included) onto the ¼" threaded nipple

of the compressed air stapler.

The connection locks automatically.

♦ 2.) Now connect the other end of the com-

pressed air hose to the (ﬁlter) pressure

reducer on the compressor.

Filling the magazine

♦ Press the magazine lever and pull back the

magazine cover until it stops.

♦ Place the appropriate fastener material (nails,

see ﬁg. B or staples, see ﬁg. C) in the magazine

. The staples must be placed on the bar of

the magazine .

♦ Slide the magazine cover forwards until it clicks

into place.

Operation

♦ Load the magazine of the compressed air

stapler, as described in the section "Filling the

magazine".

♦ Set the correct working pressure using the

pressure reducing valve (not supplied).

NOTE

■ Make sure that you do not exceed the

maximum working pressure of 8 bar on the

appliance. An excessive working pressure

does not mean increased output; it merely

increases the compressed air consumption

and accelerates appliance wear.

♦ Switch on the compressor.

Run the compressor once until the maximum

tank pressure has been reached and then

switch oﬀ the appliance.

♦ Place the appliance on the workpiece and pull

the trigger

NOTE

■ The compressed air stapler is

equipped with a trigger lock

The fastener material does not leave

the appliance until the opening of the

compressed air stapler is pressed against the

workpiece and the trigger is pressed.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 285202 PDT 40 D3 in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 1,04 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside IAN 285202 PDT 40 D3 Manual

Product: