746433
20
Zoom out
Zoom in
Previous page
1/75
Next page
16 
GB
IE
PDSP 1000 B2
The nearer you are to the workpiece, the
smaller the dispersion pattern and vice versa.
Do a test run on an old workpiece to find out
the correct distance/working pressure and
avoid excessive reflection from your workpiece.
Switching on:
Set the control dial
to "1" to open the air
outlet.
Move the compressed air sandblaster close
to the area to be worked.
Press the trigger to start operating the com-
pressed air sandblaster gun .
Switching off:
Release the trigger
to switch off of the com-
pressed air sandblaster gun .
Set the control dial to "0" to close the air
outlet.
Disconnect the appliance from the compressed
air source after you finish work.
NOTE
First detach the hose from the compressed air
source before disconnecting the supply hose
from the appliance.
In this way, you avoid uncontrollable thrash-
ing about of the supply hose.
Collecting bag for sandblasting
material
NOTE
Do not re-use surplus sand-blasting material
from the collecting bag
until it has been
cleaned.
You can remove the surplus sand-blasting mate-
rial which has collected in the collecting bag
via the zip fastener or use a screwdriver to undo
the screw clamp and remove the collecting
bag from the appliance.
Troubleshooting
Fault/possible cause Remedy
No material flow
The air is not dry
enough.
Install a water separa-
tor in your compressed
air system.
Air pressure too low
Increase the output
pressure of your com-
pressor.
Attachment not sitting
correctly
Ensure that the attach-
ment is firmly on the
appliance and that
no air escapes at the
sides.
Blocked sand-blasting
material pipes
Check that no lumps of
sandblasting material
are blocking the pipes.
Preferably, use a
blow-out gun to clean
blocked pipes.
(Wear safety gog-
gles!) Also check the
tank outlet opening.
Sand-blasting pattern not as expected
The air is not dry
enough.
Install a water separa-
tor in your compressed
air system.
Sand-blasting material
grain size not uniform
Replace sand-blasting
material.
Sand-blasting material
impure
Clean/replace sand-
blasting material
The attachment is worn Replace the attach-
ment
Other defects
Please contact an expert or your retailer.
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 285195 PDSP 1000 B2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 285195 PDSP 1000 B2 in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 0,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info